Browse by brand, ask questions, or call 1-336-969-0110 for faster service.
Found 1049 results.
Showing page 3 of 21.
Ms.Buse Zehir: Dear Sirs,Im looking for a cnc Servo Driver control card according to following specificationsVELCON??VLAST-070P3V-XX3 phase 200-240 VAC 50-60 HZThe cards photos are in the attached filesLooking forward to see your reply as quick as possibleBest regards
Reply
Ben Hur Aguinaldo Jr: Hi,Can you assist us in this inquiry? -velconic servo motor VLBST-37030-AB -velconic servo controller VLNBL-070P30-AC1 Regards,BEN HUR AGUINALDO JR.RNM DYNAMICS (PHILS.) INC.Tel. : (632) 842 7545Fax : (632) 842 7558email : ben.a@rnmdynamics.com
Reply
Ben Hur Aguinaldo Jr.: Hi,Kindly provide pricing and availability for the item below.We badly need this please give best price and leadtime.Servo Driver:Velconic BS Servo Controller T SeriesVLNBT-050P3V-AX1Regards,Ben Hur Aguinaldo Jr.RNM DYNAMICS PHILS., INC.Tel.: +632 8427545Fax: +632 8427558email: ben.a@rnmdynamics.com
Reply
mr. shamim alam: Dear Sir, We have Iwasaki-TR-25 6clr, UV waterless offset label press. For that machine the Main Motor is as follows: Velconic BS - Servo MotorVLBSE - 55040Sr. No. : 55400345.5 KW4000- RPMTOEI Electric Co. Japan-35Kg for above motor following is the drive Velconic Software BS Servo AMPVLASE - 150PSource 3P 200/220V AC 50/60HzSerial No. ; 24R20502041Motor Type ; VLBSE - 55040TOEI Electric Co. Japan In this machine we are facing following problem. as soon as we put on the mains switch of the control box, for a moment a display on the servo shows r 0 , & changes to A.L- 3. the dot after 3 is blinking. Bcz of this machine is neither inching nor running..Mains voltage to the servo is measured. It is 200V Phase to Phase. We thought may be little more voltage required, so we gave 220V phase to phase. Still the problem is same.Plz advice solution as earlier possible. With warms regardsShamim Alam
Reply
Anang Suherman: dear shamim,I think that is some problem with hardware ( IPM Modul ) . Try to change itsand check all parameter before you run again . happy nice day best regards,Anang suhermanIndustrial Machine Technical Engineering
Reply
Anang Suherman: dear shamim,I think that is some problem with hardware ( IPM Modul ) . Try to change itsand check all parameter before you run again . happy nice day best regards,Anang suhermanIndustrial Machine Technical Engineering
Reply
chandra waju: Dear Sir,I need some informations about Velconic Toei Electric VLBST-04030-G and Velconic Toei Electric VLASE-01087-187.I was search this device in the internet, but i have not find information about it. Can you help me to give some information about it atleast the specification? Please....Thank you very muchChandra Waju
Reply
Irma Rakhmawati: Dear Sir,I would like to have information about Driver Velconic type VLTT-010 PR-2I would like to buy it.So please give me information how to buy this item.Kindly please advice.Thank you,Irma
Reply
Jaime Lopez: Hi, I have a Velconic servo motor that I need to repair.Model VLBST-04030Please, can you send me Information about the procedure to repair this motor?I will appreciate to much your helpRegards
Reply
pandaya: Dear SirWe have Servo Motor Velconic Type VLASE-020P-051 Please give me information Specification and How to Program that servo motor.Thanks about your attention.Best regard Pandaya
Reply
pandaya: Dear SirWe have Servo Motor driver Velconic Type VLASE-020P-051 Please give me information Specification and How to Program that servo motor.Thanks about your attention.Best regard Pandaya
Reply
glenn: I have a few units of velconic drivers such as VLNDT-100P3V-XXI are faulty, can i know who do i need to contact for advice and repairs.
Reply
Oleg: Sirs,I need to repair VLNBT-100P3V-EXX.It is SERVO module of CT Toshiba Aquillion 4 slice.I see message AL 902.
Reply
andi kurnianto: dear sir,my name andi kurnianto, i want information with velconic vlase-150p-189,because my problem with it,my be you have manual book or information wiring in block product,iam very much with your attention,please i want help you ..urgent.regardandi kurnianto
Reply
HARMINDER SINGH SAINI: Dear SirWe have a servodriver VLASE 150-P which is not working properly. Please quote to repair it. How much is the shipping charge from India Oin Code 110039.
Reply
Adison Kh.: I would like to request for help from you due to I found servo motor model VLBST-3703 were malfunction that I could not find and order the new one to replace. Can you help me to repair or them or not? If you can please send the detail to me.Thanks and Best regards,Adison Khangrang
Reply
emma: good day to you have you got any agents in south africa for velconic electric cards this is quite urgent if you can get back to me please
Reply
vijay patel: do u have any agent or repair centre in India. if it is near by india please specified and reply.regards,vijay
Reply
somsak kongnuket: I want to know about supplier velconic servo model VLASE-505P-142 in thailand thank.
Reply
Throngpon Rathbumpoeng: I want to manual for VLTT-010P andI want to know about supplier velconic in thailand thank.
Reply
agustinus: I want to manual for VLTT-050P andI want to know about supplier velconic in Indonesia thank.
Reply
jaisingh: i am working in textile company & i want velconic drvie mannual for guidence only.my company use toyata jat 170 Loom in weaving section.so plz helpfuli am wating for ur promt reply.
Reply
VERG: ITS VERY GOOD SERVO AMPLIFIER BUT NOW GIVING MESSAGE OF COMUNNICATION ERROR.
Reply
luis Gregorio Almendarez: Need a product and instruction manual of the Velconic VLASE-020PZsource: 3P 200/220VACMotor type: 24L26209813Have one drive with intemitenet failures. Need to review and maybe to replace
Reply
AKASAKA ELECTRONICS LTD: Alarm message AL1 is displayed on the drive as soon as the motor drive command is given.
Reply
khalid baig : dear sir, i need manual of velconic vltt-050p bs-sevo amp.please i need it urgent help me out.thanks.khalid baig
Reply
s. sunthar singh: Dear Sir,We have MPU and we face problem in it. Error shows 321. MPU details are ( DOA-32, DIA-32, MCA68-001, PSA-05Will you be able to repair the same and send it to us. If you have the new one, please let us know the price.tks
Reply
Bill Sawyer: I am getting fault message on master drive AL902. I have no way of knowing what this is with no documentation. I put another slave drive drive in and error remained. Any suggestions and where can we obtain documentation on drives with listing of error codes. Thanks.Bill Sawyer
Reply
Emillie Getalado: To whom it may concern, We are Kuri Technologies Company,a trading for spareparts and supplies. May request for a quotation for VELCONIC VLPST-012P2V-XB We urgent need this item, your immediate feedback is highly appreciated. Thank you.Sincerely,Emillie GetaladoSalesKURI Technologies Company
Reply
Gerardo Pinales: I?m having some trouble with a old velconic drive VLASE-020PZ, but I can?t find any informacion about it, I?ll appreciate your advice or support to get or send me this manual.best regards
Reply
Virachan Chaichana: Dear Sir,I need you to quote a full set of VLTT-050P motor drive. I need it for replace the old one I have, but the drive was broken and very hard to investigate and replace only a peace of IC or condenser, I need a full set of this control unit.Please quote base on DHL shipping to Bangkok, Thailand. Thank you.Virachan. +6681 492 0192.
Reply
Krishan Kumar: I need Operating Manual of Velconic Servo Drive VLAST 070P3
Reply
Dave Henderson: I have a VonWeise gear motor model # V02387AB62 serial # D285 that has a cracked gear case casting and I need a replacement. The casting Model # is VW62 and has the part # W2974 on the inside. Is this something you can help me with or advise who could?Thanks,Dave
Reply
Linda Orak: I have a VonWeise motor model L3096 that is used in a lift chair. The motor stopped working. I was wondering how to get a replacement motor. Can you help me? Ive tried locally with no luck.Thank you,Linda
Reply
bill smaney: where can i get parts for von weise lift chairsmy phone # is 920 829 5094
Reply
Kristine Polzer: I am looking for gearcase cover for a Invacare LC53 Lift chair Serial #97C77045 with a Von Weise Motor.
Reply
Ron Vocht: I may need a replacement motor for an electric adjustable bed. Where can I find a Von Weise Gear Co. motor, model VO2898AB76 ? It is a thermally protected electric motor. Volts-115, AC, Amps-1.4, Hz-60, Ph-1, Hp-1/10, Ratio-19:1, Serial-E-78, Shaft-7/16. Does this company still exist?
Reply
Ken Bensinger: I may need a replacement motor for an electric adjustable bed. Where can I find a Von Weise Gear Co. motor, model VO2898AB76 ? The motor is working but the gear box is bad.It has a broken flat bearing and a broken washer in it. it also has a stipped plastic gear.
Reply
Paul Bowers: The bolt holes broke out on the head end. I need a new head cover.
Reply
SUSAN: I AM LOOKING FOR A VON WEISE STEP COVER MOTOR MODEL -14943674, 12VDC 8.7A 24:1 SN-L1407. THIS IS FOR THE STEP COVER IN A NATIONAL RV. IF YOU CAN GIVE ME ANY INFORMATION ON WHERE I CAN LOCATE ONE OF THESE THAT WOULD BE GREAT.THANK YOU
Reply
Ron Kadesch: I need a working or parts for a Von Weise lift chair operator # 908. Some other # on case- Model VO7647AA76U, also VWE-3 DCF. The motor runs, but the lift shaft doest move. I think the nut or drive shaft must be striped. Can anyone help with parts or info??? THANKS, Ron
Reply
Debra Fauvor: I purchased a lift chair from Sears 7 years ago. They used to run a stupid ad campaign Buy it at Sears, get it fixed at Sears. Now they dont want to fix a damn thing. Do you know where I can get it fixed?
Reply
Chuck Henry: I have a treadmill with a VonWeise V05119AJ76 motor that has a 19:1 gearbox on it. The output screw shaft is bent, but otherwise the unit works fine. Is it possible to get just that replacement part?
Reply
Paul Priester: Do you have replacment parts for camper jacks
Reply
Gary Abbott: Vonweise model # v00310araa needs new seal, bearing and refilled with gear oil
Reply
herman wilson: the chair stop in lay out mode I could hear the motor runing but it would not move the chair to let my mother get out of it thank you wilson
Reply
Richard Sieger: I have a VonWeise Gear Motor Model V05679CB76U, Serial B1999 that has stripped the main drive gear. I need to replace it. Its the largest gear in the gearbox, which connects to the output shaft? I would also like to purchase a maintenance/repair manual for it, if one is available.
Reply
jessie burns: chair will go up but not down
Reply
Larry Taylor: Switching the wires in hand contoller to raise then switch wires again to lower chair. I believe the switch in the hand controller is bad and needs to be replaced. The motor works ok.
Reply
victor: I request to quote engines for clinical bedsattevictor
Reply
benny stuben rauch: I need the two relays or pc board and relays how ever the part comes for a Von Weise lift chair motor model v05679DL76U serial C2800 cell phone (248) 240-3015 or home phone (586) 777-5469
Reply
Ruth Sprouse: Hand control on Vonweise lift chair not working. Chair only works occassionally. Goes up but will not go down. How do I get a replacement hand control, what is the cost for a control and how long is the warrenty?Please call 309-341-3456.Thank you
Reply
jon mitchell: have invacare chair w/ vonweise drive. up/stand works ok, down erratic. have to tap relay to get operation of down/recline. looking for repacement relay board pricing and availability. m# V07647AA76U ID# IDI225IBN0252 OPERATOR#H3100 JJS4000M800 VWE-3 INVACARE CHAIR DCF M#LC86 S#00I953361 115vac 60hz 1.0amp 169:1 ratio DC supply P/N PS-00000004 40vdc 2.5amp
Reply
Mike Baldarelli: We are looking for a new motor or the upper housing which connects the motor to the chair. The model number is: VO5789AD76U - Serial number: HO896The following numbers were also on the motor: K14003-0001 7190-1935 Type - 90B1Please let me know if you could help.Thanks,Mike
Reply
Alice Hanna : I am looking for a replacement motor for an electric bed. Model #V05789AG76U Serial # H2997 P/N 7190-1935 type 9081can you supply me with one or tell me where I can find one.
Reply
neal: the drive gear is all broken up in my lift chair could you please help me. i am trying to take the gear out but there is a pin that runs threw the drive gear how can i take the pin out i would like to see a diagram if you have one thank you neal
Reply
leon pemberton: i need a drive gear set fore m.vo5679dl76u s.c2700 chair
Reply
gerald laws: hello the mane gear that makes the chair go up and down is striped out it is a plastis gear on top of the motor that connects to the input shaft what do i need to do to get the gear or have you fix it please resboun thank you and god bless geraldlaws@bellsouth.net
Reply
Peter Winter: I am hoping that you will be able to either supply, or tell me where I might be able to locate a replacement for Von Weise gearmotor, Model #V 056 79CB76U, 115 VAC 60 Hz, 1.0 AVWE-1 Ratio 169: 1This is a motor from a lift chair manufactured by the Cleveland Chair Company which is no longer in existence. Any assistance you could provide would be most appreciated.
Reply
THELMA : MY MOTOR DONT WORK SAME MODEL AS YOURS.DID YOU FIND ANY PARTS?OR EVEN ANOTHER MOTOR?IM LOOKING TOO.PLEASE LET ME KNOW.
Reply
Peter Winter: I am hoping that you will be able to either supply, or tell me where I might be able to locate a replacement for Von Weise gearmotor, Model #V 056 79CB76U, 115 VAC 60 Hz, 1.0 AVWE-1 Ratio 169: 1This is a motor from a lift chair manufactured by the Cleveland Chair Company which is no longer in existence. Any assistance you could provide would be most appreciated.
Reply
Steve Webb: Can I get a replacement motor, if so how much will it cost.Model# V05679DL76UID# ID10724NO117Serial # D1700 JJ54000MP00Made by Fasco CompanyCall me at 210-416-7789
Reply
Randy Robinson: I would like to know if I can purchase parts for the chair actuator that I am repairing? The large gear that is attached to the screw need to be replaced. The model #v05679dl76u ser #g1000. If not can you direct me to somone that handles the parts for these units. Thank you Randy
Reply
Arnold: I have a vo5679cb76u and the electric board is burned
Reply
Jerry Landseadel: I have a lift chair made by Golden Technologies, INC. with a VonWeise lift mechanism, model number v05789AD76U, serial number A1497, 115 vac, 60 HZ 1.6 A. The chair is in excellent shape but the mechanism broke. I need a new part.
Reply
Dave Burnham: We have a VonWeise Motor for our Manitowoc Ice Machine. The shaft is broken that turns the auger. The Transmission model number is WW62. Can we get the transmission without the motor or does that come as a complete unit? Please give us a cost and availibility.Thank You!Dave Burnham Tarta1127 W.Central Ave.Toledo Oh, 43610419-245-5234
Reply
Mary Anderson: Looking for a Von-weise remote to operate an adjustable bed. Any help?Thanks
Reply
Rob: I have a patient with a lift chair that will move in the up position but willnot move in the down position. i am assuming that it is the remote and not the motor. the model Number is :v05679dl76the ID # is ID84072n0073Serial # JJ54000m800The patient uses the chair for sleeping and requires the chair to be fixed ASAPPlease get back to me Thank You Rob
Reply
Rob Johnson: Having the exact same problem with chair here also. Has anyone found out how to fix this???
Reply
Jo_Anne Guigue: the model V07508AW76U Serial A0902 I found these information on the motor I need the remote . How much is the remote. I live in Canada
Reply
gregg: need to find a wireless remote for an adjustable bed. bed has von weise motors with massage motors, model number V07594AB79U.Trancemitter box model number 3433. frequancy 433 mhz rev1.1 . Any help please.
Reply
Aaron Tam: I have a Von Weise gearmotor, inside the gear box, there is a plastic gear assembly driven by the main shaft. The plastic gear is broken.Can you tell me where can i buy the replacement of the plastic (nylon)gear asssembly in Ontario, Canada if posible.Thank you
Reply
unangeRomonab: MARGARITA TRICIA d and down-to-earth Tyler Perry DEMETRICE
Reply
Anke Hamalian: need to replace this motor.Where I can buy?
Reply
Jim: Hi, Need switch for handheld controller. Have one ?? How much ?? Also, service manual ?? Thanks, Jim
Reply
Michael L. Walker: I have a King Koil elect. bed. About year 1981.The wormgear that drives the up and down motion of the bed, has come out of the motor. I cant tell what is supposed to keep the end of the wormgear in place in the motor. What I am calling a wormgear is a long geared shaft, about 1/2 in in diameter. The back end of the wormgearshould be attached into the motor, as the bedframe rides the wormgear to raise and lower the head of the bed. Any info about what is missing, or why this shaft will nor stay in the motor would be appreciated. I am able to make repairs, if I knew what part or parts are missing, and how to purchase them Motor/drive unit is Von Weise model V03232A876 1/10 h.p. 1.4 amps. 19 to 1 ratio. Serial A-80. Thanks for any help you can provide. Michael Walker.
Reply
Gary Marsalis: I have a Cleavland Lift Chair with a Von Weise Model Number V07647AA76U Serl. Number K3000,115VAC, Ratio: 169:1 gear motor/actuator. I need the power cord with plug that plugs into the motor control. The plug is white plastic with the female pins in it, it mates to a plug in the control that has two male pins in it.
Reply
millie hinojosa: I need the remote control power cord for lift chair serial number L0201. model v07647aa76u
Reply
John Williamsen: We have received a photo of what we believe to be a VERSATYME electo/mechanical controller. It is on an LA Water brand water treatment unit. Question is, if we send the photo to you could you identity the brand as a VERSATYME? Please e-mail back.John
Reply
Howard Bassel: Do you supply this type of part or should I go directly to the Company. If you suggest tthat I go to the Comapny, can you supply an e - mail and a phone number.Thank you,Howard Bassel
Reply
Valeria Sharova: Dear Sirs,We are looking for a servo-motor VELCONIC VLTT-050 PR of TOEL ELECTRIC Co production with an additional built-in plata B0 009202.We also need a servo-motor VLBS-A22012 of a production of the same company.All for use in our Bobst SP 900 machine.Hope for your quick reply.Thank you very much in advance.With best regards,Valeria Sharova
Reply
NGUYEN HUY DINH: 58/5A Huynh Tan Phat street, district 7, Ho Chi Minh city, Viet Nam Friday, 5 May 2006Dear Sirs,We have a servo amplifier VELCONIC VLTT-010SR of TOEI ELECTRIC Co production, but we dont how to use it. So we want to have a users guide for it. Hope for your quick reply.Thank you very much.With best regards,Nguyen Huy Dinh
Reply
VIJAY PATEL: WE ARE FACING PROBLEM IN VELCONIC SERVO AMPLIFIER REGARDING HIGH FAILURE OF TRANSISTOR MODUEL 6DI75A050. FOLLOWING SPECIFICATION OF SERVO AMPLIFIER:-VLASE-050P-166SOURCE - 3P200/220VAC 50/60HZMOTOR- VLBST-24030.
Reply
Mark: Can anyone guide me to a source for an older series amp RAD330..Thanks
Reply
khemananda: we need parameter vlase 020p
Reply
joel p. adorable: How to reset the alarm 10 which is trigger to the monitor, and what will do of this.
Reply
athar javid: Dear sirplease send me vltt servo amplifire manual best regardsAthar
Reply
NO SEUNG HYUN: VLASE-150P MANUAL
Reply
DHIRENDRA DUBE: Dear Sir/MadomWe arecfacing problem in VELCONIC SERVO AMPLIFIER Type VLPSV-070P#-AB,if possible pl provide us the manual of the same
Reply
EUGENE GETZ: WE ARE PROGRAMING THE ABOVE AMPLIFIER USING THE PRG-90 PROGRAMMER. WE WERE ABLE TO PUT IN ALL OF THE PARAMETERS BUT WE ARE UNABLE TO GET OUT OF THE EDIT COMMAND. THE DRIVE WILL NOT WORK BECAUSE WE ARE STILL IN EDIT. THE DRIVE IS BRAND NEW AND HAS THE SAME PARAMETERS AS OUR OTHER DRIVE. CAN YOU TELL US WERE WE CAN GET THE PRG-90 MANUAL AND ALSO THE AMPLIFIER MANUAL. WE WILL ALSO NEED OUR OLD AMPLIFIER REPAIRED
Reply
Shahzada Waqas: please reply me if we can get a manuall for this servo motorVLBS A22012Sn.2211090model 1989
Reply
Koay: My VELCONIC VLNBE-050P-XP servo drive have error code 05.What is this error 05 means ??Tqvm !
Reply
Luis Carlos Hernandez: Need to have this unit repaired, power supply does not have any output.
Reply
magdyseliman: ive vlase-050p servo amp vlbse-22012 motor type ihave error 18 ineed to repaire servo amp or ineed new one
Reply
Cheng: HOW REPAIR A FAULT. It is A.L -04
Reply
khemananda: we need parameter type velconic vlase-020p
Reply
khemananda: we need parameter servo amp velconic vlase 020p
Reply
mustafa: Hi me and alarm codes sema velconic vltt 020pn electricity as soon as possible if you send description should be good ..
Reply
Martin Gauthier: We have 3 drive VLASE-010p-058 and We are lokking for the programming and hardware manuals... Do you know were I can find them?
Reply
RJ SINDAC: Hello Sir/Madam,Good Day!Currently, we are facing problem one of our machine,Servo Motor Alarm, Alarm 32 on Servo driver with SN. VLNBE-050P-APcan you give us some information on the said driver for easy troubleshooting. ThanksRegards,Rj Sindac
Reply
YVV SN RAJU: currently servo problemservo details VLASV-012P2-HX 200V-ASSY 0000PRESENT AVAILABLE PLACE & SUPPLAR NAME &ADDRES
Reply
Rajkumar Sharma: Please send quotation of velconic servo ampliier.Model VLPSV-070P3-ABPlease send quotation of data cable and software loader.Thanks with regards,Rajkumar Sharma,Abhitex International,Pasina Kalan,GT Road,Panipat - 132103HaryanaPh 09896539937
Reply
RAMA: SERVO ROTATION PROBLEMSERVO MOTOR NOT COMPLITE THE FULL ROTATION
Reply
Chandresh: Dear sir; We have facing frequent problem in our VELCONIC-VLAST-015T Servo-amplifier with control boards in our toyota looms-710letoff motion unit. Its specification as under. specification=VELCONIC-VLAST-015T ASSY=5300 0.NO.J9202-20021-0E SOURCE=3P 200/220VAC 50/60HZ OUTPUT=17.0A(PEAK) SERNO.=4B020504851 TOEI ELECTRIC CO. LTD;MADE IN JAPANFAULT=1) IPM ERROR 2)LET-OFF EMERGENCY STOP N& LET-OFF AMPLIFIER ERROR 3) LET-OFF TENSION NOT MAINTAIN AS PER SET VALUE So please give the guidence /manual for the above said drive. Also please give the testing method of such drive in electronics lab.Also give the address for repairing of such drive/amplifier located in india.Chandresh
Reply
N BALASUBRAMANIAN: Kindly provide contact details of your distributor & service centers in India
Reply
V.VIJAYA KUMAR: Dear sir, We have a servo amplifier VELCONIC VLTT- 80 PIN of TOEI ELECTRIC CO PRODUCTION, We are facing problem in servo amplifier which is showing fault indication VAS. Servo motor is not rotating due to this fault. Kindly, give trouble shooting procedure to resolve this problem at the earliest.I hope for your quick replyThanks & Regards,V.Vijayakumar
Reply
HUYNH NGUYEN DUY PHUC: Dear sir,I have a servo amplifier VELCONIC VLPST-012P2L-SX and a motor type VLBST-Z02030S-BGU of TOEI ELECTRIC CO., Ltd., but I dont know how to use it because there are no userguide of it. Its made in Japan in 2004 and I took it from my teacher, without any userguide. Kindly, I need you send me and catalog or userguide of it to use it efficiently.Thanks alot.HND.Phuc
Reply
martatan: I need a velconic manual type VLNBE-020P-FP.How can I Do?
Reply
DANE NEUTZ: IM LOOKING FOR SOMEONE IN THE U.S. TO REPAIR DRIVES AND MOTORS.WE ARE A U.S. AGENT FOR A LINE OF WIRE FORMING MACHINES THAT USE VELCONICS UNITS.
Reply
THANGLE: motor Model : VLBS-075-120-S , Qty 2pc , maker : VELCONICThanks Thangle MB: 0989.881549tell: 84-08-4461459Fax : 84-08-4460078
Reply
FEG Components (Ipoh) Sdn Bhd: Can you give me Velconic agent at Malaysia?Thank youBest RegardsChin
Reply
madhukar s.shinde: sr.no: 0662496 of Toyita Air Jet loom.
Reply
Jonathan Albert Ocampo: Dear Sir / Maam,Kindly send a formal quotation for the products.Brand: VELCONIC1.Servo Motor, VLBST-Z02030 200W, 1 QTY2.Servo Motor, VLBST-Z01030 100W, 1 QTY3.Servo Motor, VLBST-Z04030S-BGU 1/15, 1 QTYDo you have a distributor here in Philippines?Thank you.Best regards,Jonathan Albert OcampoPurchasing StaffPro Board Technology Services Corporation
Reply
Ganda Kusumah: Dear Sirs,We are looking for a servo-motor VELCONIC VLPSV-035P3-RB TOEI ELECTRIC Co for printing machine.Hope for your quick reply.Thank you very much in advance.Best regards,Ganda KusumahPT. Dawee Electronic Indonesia
Reply
Gregg Luebbering: I have a problem with a Power Track Jr. ventilation amchine that you manufacture for Hired Hand of Alabama. How can I see a parts diagram of this and determine the part number I need to repair this unit? Thanks so much for responding back to me.
Reply
Jose Luis Bravo: Please be so kind to quote: Two pieces of part number AX915034P Board Driver for Versaply Label MachineThanks so much
Reply
Don: HI, I have a versapply 9100R-40 that has been in storgae for a while. We would like to attempt to use it but we have no operators manual , schematic diagrams or anything to work with. Do you have any liturature to help. We are willing to pay for it. We also have a 77 Doboy supermustang wrapper we are looking for information on. Thank you for your time and God Bless America, Done-mail-- DonandVon@comcast.net
Reply
Don Page: HI, I have a Versapply labeler and its in good shape and it was working ok but someone screwed with the controls on the circuit board ( AX915033P ) and I cant seem to get it synced with the prduct on the conveyer. It sometimes spits out three labels instead of one. We are atempting to use it on a single wrapped cookie 4 by 4 and 1/2 inch thick . Would you have any drawings or instruction on what pots does what to the delay etc. There are several on the board. I also have adjustments on the product sensor Sunx CX- PRVM3. Any help would be greatly appreciated. Are there any download sites for instructions on setup you know of for this vintage of Varsapply? Thanks and God Bless America, Don
Reply
Craig James Titzkowski: I need to know how to get replace ment parts and a manual that shows the parts so I can order the part I need that would be of great help. I work maintenance for Trident Seafoods and am just doing some tracking down of info for my Chief. So we can order parts we need
Reply
cal haines: These are 3 UDK5107N 5 phase drivers that need repaired.
Reply
Stan Thomas: Lift chair wont go down. Checked out and lower relay is sticking. Tapped with screwdriver and it started working. Relays are soldered to the board... The chair is fairly old and customer doesnt want to spend a lot on it...as usual. Please give me an estimate. Thanks, Stan
Reply
melanie hamilton: We dont know if the bed controller is faulty or if its the motor unit being controlled. Would appreciate any information you might have regarding which it might be. If we know that its the controller for certain...Numbers on control unit:VWE-PD-M003 (zero zero three)Serial number: 22968
Reply
HENRY McCUISTION: One way to test whether it is your controller or a motor is to switch the plug from the nonfunctioning section (Head, Foot or Bed) into the recepticle for one of the working sections, then use that control button to test the motor itself. Example: If the head does not work but the foot does, unplug the head motor and plug it into the socket for the foot motor. Use the Foot control buttons to raise and lower the head. If the head now works, the problem most likely lies in the controller itself; usually the button itself has failed and the entire controller must be replaced. I am currently looking for a controller myself.
Reply
Kenneth Hoover: Von Weise drive assy. used on Invcare adj. bed(mod#V07564AS76U) will raise and lower the head but when in the low height position ,3 to 6 inches, the drive appears to slip back a couple of inches. Keeps slipping back until you reach acertian point then stops slipping back. When just raiseing and lowering works fine. Iam qualified to repair unit. Thank You, Ken Hoover.
Reply
Ben Rowden: I lost my remote for this bed and was trying to program a logitech harmony remote to control it. Do you know if this is possible?Ben
Reply
Rich Angel: I have an adjustable bed that appears to have your motor/actuator. The model on the motor is VO7564AS76U. The connecting ring located on the top of the motor has broken and I would like to purchase a new one. Hopefully you can sell/provide that top piece but if I need to purchase the motor and assembly that is fine.A sticker label is on the motor with the name Dunntron and the model number given above. The serial number is KO900 and there are other numbers without description on that same label ... including 100150 and VWG-71; also E32557.Thanks!
Reply
Chetan: Need to fix bed the motor want come on need new control
Reply
Maria Bartolotta: I have two twin ajustable beds...together as a king-size.One bed is no longer adjustable. Is there someone in my location that does repairs for this bed?Model: V07564AS76U115 VAC 60 HZ 2.8AClass B INSUL 40CThermally protectedSerial F2101MO100150VWG-71E32557
Reply
norman: Smae problem of not holding its position and the head position slowly sinks back down. It only taked to cotter pins to replace this unit on the bed frame so I would like to find a replacement unit if possible.
Reply
Equarborirurn: Where I can find good quality films?Can anyone help me?
Reply
OblilkFib: Hi friend i am new to this. Just thought that i would say hello to everyone! dont really know what else to say.I love texting, nothing else to say so bye
Reply
mike hetherington: I need the controller for my adjustable bed. The only label I can find is on the motor and it has # V07564AS76U. The name is difficult to see but it looks like Dunntron Thanks
Reply
Jay Blackmon: i have a servo alarm the cursor beside the r o. is blinking.i have no manual in english
Reply
hamad al sanad: Hi There...Iwould like to have the specification for:1-Air speed Sensor (model 7100_ a part number 07212-2A)2- Altitude sensor(model 7000 _ a part number 52772 )3- air temperature sensor (platinum resistance thrmometer _a part number s9690pl1z12)
Reply
Pascal Cesar: Dear Sir/madam,We have electrolux wascator model W335MP washing machine the PCB control unit LCD screen is not functioning as the pin is broken off from the LCD screen.This LCD screen has these Label No1 - made in taiwan by FUTABA FV609 G Label No2 - your company label with P/N 471 89 89 -04Label No3 - 438711808 180 & 335 PE02b CHWe would like to purchase a new LCD screen.Regards,Mr Pascal Cesar
Reply
Ronnie Bahari: Board INFO:Vellinge ElectronicsP/N 487 18 15 31 REV. 2.80133-0216-S:801Process Module REV. 3.11=====================Hello,I have a problem with this drys board. This board is used on a WASCOMAT dryer model # TD 30.30 The micro processer is bad. Could you please advise what to do and how much @ it cost.Thx
Reply
John: I need to buy the TSM board and the control board for Emotrons MSF soft starter. Possible P/N is 99-73-02 (Vellinge) or 01-1660-010 (Emotron).ThanksJohn
Reply
Lee: Hello,I like to order a control board (Vellinge Electronics P/N: 99-43-06, 9824-0011 S:002, 01-0038-00 Rev:) of Emotron Flowdrive UF40-089-540EThanks!Lee
Reply
luc havelange: HelloI have several damaged printed card from a wash machine electolux wascator model w 365h .The display screen on those main cards are broken .The cards have your number P/N 471 89 88-11 rev 004 s: 008 0142 - 0082 .Is it possible to order those screens ??? thank you in advance luc
Reply
Stephanie Findlay: Hi I am looking for a bit of help do you know how much model 365h would be worth ?
Reply
Wincent pang: We would like to purchase a new LCD screen.This LCD screen has these VELLINGE ELECTRONICSP/N 82-1000-02 0047-0094 S:019
Reply
Igor Florjancic: Hello!Please, tell me wich display is in this electronic bord:Vellinge electronics ABP/N 82-1000REV:000 S:0239709-0001MAC 12Ver 1.00C960904 94F7
Reply
Dees: Dear sir/madamI have machine that uses a vellinge electronic CPU p/n 560 60 01-02 that has a fault on the comms port J11. I have a new spare one in stock and would like to replace it. Do I simply replace the CPU and transfer the 3 memory chips and reboot or does it need to be reprogrammed?.I am a certified electrician and electronics technician, your advice will be greatly appreciated,Will I be able to send the faulty one to you for repair?. Please forward me all relevent details.Thank youDeesFacilities EngineerBiomed LtdOffice + 64 9 8155405DDI +64 9 8155182
Reply
Paul Wareham: Require testing and possibly repair.
Reply
clayton bennett: Do you repair and/or calibrate the Velonex V3510 surge generator?
Reply
Preston johnson: I have 2820 modules and 1210 modules they work but will sell for coresThank,s
Reply
martatan: Whats alarm nember 44 in velconic servo type VLNBE-020P?
Reply
SMAILL TABRIZI: Whats alarm nember 44 in velconic servo type VLNBE-020P?
Reply
romano igot: Hi sir/ maam,
Reply
huynhphuc: I need the datasheet of Toei VLPST servodriver. Can you tell me the way to using the servo. Best regardHuynhPhuc.
Reply
santosh: very nice drive but drive manual give me
Reply
romano igot: Hi sir/ maam, We are one of the users of your product. The driver of servo motor. Our company is Autoveyor Phils. Corporation. I, as a representive would like to ask a favor from your good office to help me on how to find or search a manual for servo driver the VLPST-012P2V-XBThank you and more power to you!
Reply
gaojinhua: Velconic VLPST-012P2V-XB Manual
Reply
Muhammad Abubakar: Respected sir,i have recently purchased the said driver. it is used and i need its manual to make it operate able. Please send the manual so that i can use the product. thanksSerial NO. is. T012P208451
Reply
Andres Pulla Mendieta: Dear Sir please hel? to salve the error AL 21, are you could share the manual for these Servo controller
Reply
Lee siong foo: The servomotor brand velconic:vlase-020b,When push start button the motorhave no function.TqLee
Reply
ken bodrogi: I have a small pc board that I think needs repair. part # 117770-01vellinge electronics.
Reply
ROBERT GOMEZ: CAN YOU REPAIR HOSHIZAKI ICE MACHINE CONTROL BROARD THE NEW ALPINE BOARD AN THE OLDER MODEL IF YOU NEED MORE INFORMATION LET ME KNOW THANK BOB
Reply
Joe Pieri: I have a small pc board that I think needs replacement part # 117770-01vellinge electronics. This assembly is from eureka vacume Mod# 6993A. Could you supply a new one?Thank you
Reply
Landspital University Hospital Iceland: we have few pc boards for repare, and like to start on above board We like to get estimate repair price.regards.Robert Th. BenderLandspitali University Hospital Icelandtel. +354 8950500
Reply
Aysel Uyar: Dear, I urgently need the instruction manual of the driver Velconic VLTT-020P. Could you supply me some technical information about it? I have some problems in running the driver.Thanks in advance for your attention.
Reply
Jerry Mikliszanski: Please provide local service contact for Vand Dorn molding machines.Our plant is located in Illinois in Elk Grove Village.Regards,Jerry Y. MikliszanskiPlant Maintenance SupervisorPolyOne Corporation2400 E. DevonElk Grove Village, IL. 60007Office: 847 364-0011 ext. 141Fax: 847 364-0015 Jerry.Mikliszanski@Polyone.com
Reply
soonloi: I having Error Code on my servo drive(VLASE 150P).E 06And I found no button or keypad to reset, some external control panel are needed? thanks
Reply
binh: manual pdf file servo driver model toei VLASE
Reply
bodin: i need manual of vlase servo drive
Reply
Brad Gooch: I am working an an Invacare lift chair with a Vonweise drive mechanism. When I press the button on the hand control the actuator will run one direction but not the other. I have tried a different hand control (pendant) and I get the same result. When I push the button to go the other direction I hear a buzzing sound and that is it. I contacted Invacare and they will not ship individual parts. They want me to order the entire mechanism for around $350. Can you help?
Reply
Marcy Gelfand: Hello,Do you have or know of a vendor that can perform repair in Southern California?
Reply
Sheryl Espineli: Sir, We are a construction company from the Philippines. We need to urgently purchase Two (2) HYDRAULIC MOTOR for the Rotary; AB Type V12-160-TH-NH-C-000-C-160/060; APS-021-012/015; Part Numbers: 3796619; Serial Numbers: 19960117. Hope you could immediately reply this inquiry. Advanced Foundation Const. Sys. Corp.Unit 12-B Petron Megaplaza Bldg.358 Sen. Gil Puyat Ave., Makati City1200 Philippines
Reply
Dale Mitchell: Van Dorn 6es-5398-okb12 not powering on or responding to any commands. Seeking repair service as soon as possible.
Reply
Damitha Dahanayake: Dear Sir,We are using VLNBE-050P-FP and BS Servo motor VLBSE 22012 and now VLNBE-050P-FP is got aalarm 06 or 0b Please instruct us to what should we have to do and please send me user and technical English mauals.Thanks your kind corperation.
Reply
Kashup Senarathne: Dear Sir,We are using VLNBE-050P-FP and BS Servo motor VLBSE 22012 and now VLNBE-050P-FP is got alarm 16 or 0b Please instruct us to what should we have to do and please send me user and technical English mauals.
Reply
Kashup Senarathne: Dear Sir,We are using VLNBE-050P-FP and BS Servo motor VLBSE 22012 and now VLNBE-050P-FP is got alarm 16 or 0b Please instruct us to what should we have to do and please send me user and technical English mauals.
Reply
Jodi Tolbert: I need a new control cord for model V00562BF76U, type 90B1 adjustable bed by LeggettThe cord looks like a phone cord
Reply
Lynda Dobbin-Turner: We have a Restonic adjustable bed, with the above serial number on the body of the control system, but the controls were lost in a move. Need to find a replacement. Suggestions?
Reply
ROGELIO MARTINEZ: I need a flyback transformer for repair with reference is KTF215R02 manufactured by JVC and is part of the monitor model CC-15M71-MAwere I can located?
Reply
Glenn Ganley: Hello,Please quote me for the following part:PN: CC-15M71-MA QTY: 5Please quote me as soon as possible.New, un-used and original parts only.I hope to hear from you soon.Best regardsGlenn
Reply
luis gabriel sanchez: i have a QSr 3200 it?s new the equipment.the question is why change the color when we printin wthin the same file.
Reply
Almuammar Kalimi: I need my Vutek 3300 to be refurbished and upgarding of software if possibleContact me if you can do it ?00967736841089
Reply
Robert Anderson: Do you have something that will replace my two von weise gear boxs & motors? Motors still work but the gear boxes and surrounding parts (woodruff key) et all have given up... Need 2 assembled gear motors with cable if possilbeModel number - V02647AC76 (MF-05) 1/12 HP 1.4 AMP 19:1 RATIO YELLOW L1REDBLUE L2
Reply
Tammy McAdams: Do you know how to obtain a replacement remote for a Vonweise bed? Its on older model, Model # VO0562BF76U.Thanks so much
Reply
Thomas Barnes: We support several projects with Vultron sbc1022, flip-pixel traffic displays. We are seriously lacking in diagnostic and maintenance material. We also found a selection of boards marked bad. Can you help?Thank you.
Reply
Hector Juarez: VonWeise V0574 not powering on at all. Need urgent repair service.
Reply
Brad Ramcke: Can you repair an ABB Robot DSCQ 327 I/O board? One of the 0-10 vdc analog channels is irratic. The PC board is a Vellinge Electronics P/N 93-34 REV:005
Reply
Mike Bowman: I have a machine that the drive, is in need of repair. The drive in need of repair is VLASE-050P-026. I have another machine with a drive controlling the same motor model no. this is a VLASE-050P-107. What is the difference between these two drives? Can I swap them out for an immediate resolution on the one machine if the drive parameters are the same? What is approx. turn around time for repair?Thanks,Mike
Reply
Diogo: I have a problem need to change the motor speed by Vlase-050P, most do not know how to do it.I also need the manual Vlase-050P.thank youDiogo
Reply
LIM: I have Velconic VLASE-050P servo controller encounter the ALARM 5 issuePlease advise.Can send for repair?Thanks
Reply
Arturo Chaparro: Issue V-MAC II 12MS59M10 malfunctioning, unable to identify problem. Urgent repair needed.
Reply
Bobby Seale: Have a 2500 Watt Vector Inverter and need someone to repair.Model VECO 56CMaxx sst
Reply
Gia Nguyen: The Vexta PX243-02AA stepper motor is not responding to commands and causing production downtime.
Reply
Katrina : Hello, This is High Intellect CO., LTD., we have a Visi-Trak Board needs to repair. The model NO. is MVO-06283. This board is using on the BuhlerPrince, Inc. die casting machine. Please kindly provide us the quotation for repair the Visi-Trak board, or you can provide us the new one. Thank you. Regards,Katrina
Reply
Dalton:
Reply
Dalton: Alarm 18 shows POL......(MOTOR OVERLOAD INST)What does this trace back to? I believe it is the quill motor driver, but the quill zeros freely, and doesnt trip the alarm until we try and run the machine.Any ideas where to start? Driver or board?
Reply
Felipe Pliego: Good afternoon, we have a 560 60 02-01 Rev. J.9 Vellinge Electronics board and it fail so we are looking for a new board or repair it.We are looking for in USA but there are not a representative only repair service.We are a company that give technicalsupport to pharmaceutical labs in M?xicoSo we ask you help. Can you give us inforrmation about a representative company of Vellinge Electrononics in USA, Canada, M?xico or Latin AmericaThank you for you attention and we wait for your reply.
Reply
lievstroy: : My Vigoservo ARS 135-25 servo drive is malfunctioning, specifically the motor spins but no power is moving the load. The unit is no longer functioning as it should and Im seeking information on repair costs and potential replacement options. What would be the approximate cost for a new servo drive and associated labor for this model?:
Reply