Welcome to Socapel

unofficial service & repair forum

We repair a wide range of Socapel Equipment.

Ask questions, or call 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.


Why to send us your work?

To receive more information about your unit then fill out the email form below
and we will be in contact with you within 24 hours.

If you need your Socapel unit tested or repaired
then give us a call at 1-336-969-0110.
We give fair estimates and offer a exteneded warranty.

Comments for Socapel

15 comments found.
Andrew: Dear Sir! Sorry for the wrong e-mail address! This one is correct.The following problem has been occuring quite often on one of our machines for some weeks. One Socapel SAM-drive (SAM-DA-400-14N-P1N-D) stops the whole machine and displays '7 ' and 'F ' characters on its 7-segment display. At this time the PAM-controller (PAM-S1N-L4E-AP V10000)displays '0780F020 ' but the SIEMENS S5-115U PLC has no fault. This problem with the SAM can be reset by the PAM or restarting the PLC. According to the PAM-SAM Troubleshooting Guide fault code 'F ' means 'Main CPU fault (fault handler) '. Which CPU does this refer to, SAM, PAM or PLC? What else can cause this problem and what we can do, before replacing something? Unfortunately, we do not have any software tools for checking the PAM-SAM system, only for the CPU. Waiting for your quick reply on e-mail... Sincerely Yours
Reply
  
M.Saleem: The following problem has been occuring quite often on one of our machines for some days. the PAM-controller (PAM-P1N-H8F-AP-P V10810)displays '0B80E002 ' but the SIEMENS S7-315-2DP CPU has no fault. bUT MACHINE STOP, WHILE ALL THE SAM (SAM-DA-400-07N-P4N-E) ON " 1 " This is SAM Normal State.what is the cause of this problem and what we can do, before replacing something? Unfortunately, we do not have any software tools for checking the PAM-SAM system, only for the CPU. Waiting for your quick reply on e-mail... Sincerely Yours
Reply
    
Abrar Hussain: The following problem has been displaying quite often on one of our machines for some days. the PAM-controller (PAM-P1N-H8F-AP-P V10800)displays '0B80E003 ' but the SIEMENS S7-315-2DP CPU has no fault. but MACHINE STOP, WHILE ALL THE SAM (SAM-DA-400-07N-P4N-E) ON " 1 "This is SAM Normal State.what is the cause of this problem and what we can do, before replacing something? Unfortunately, we do not have any software tools for checking the PAM-SAM system, only for the CPU. Also we are facing problem 2b on our SAM unit of main Blanket motor . It happens many times in a week.Please advice.Waiting for your quick reply on e-mail... Sincerely YoursAbrar
Reply
      
Adem Ceyhaner: Dear Sir ;We have faced with the same problem you mentioned.the first problem is because of the PAM and we could not get rid of the problem.The second problem is because of the Blanket motor you should change the motor beacuse 2b means overcurrent. We have faced with the same problem and solved the problem with changing of the blanket motor.Good luck.
Reply
        
IMRAN MIAN: Hi Dear, My Machine installed Pam drive but display show ERROR 0B80E002.plz send error means or send any manual best regards,Imran Mian+92 300 2428847
Reply
          
Rashidul Hasan: Hi Dear,My Machine installed Pam drive but display show ERROR 680F005.plz send error means or send any manual Thank youRashidul HasanElectrical EngineerNoman Group of industries.
Reply
            
tariq mehmood: we Face problem in our pam Error code 0B80E010. Please help us in this matter.
Reply
    
Ersin Ak: Dear Friendswe need 1 pc. Socapel PAM-P1N-H8F AP-P V10600. If you have one of this Type, please contact us as soon as possible and give your offer.Best RegardsErsin AK
Reply
      
reza: hican you repair a pam for us.if yes email to me.thanks reza
Reply
        
sohail umer: sam and pamp quotation required
Reply
        
amjad: i want a troubleshootin manual of sam drive
Reply
    
mike: Could I get a list of error codes for this model? I have an error 25 or 52. I also have a pam to plc link lost. all other drives have no error.
Reply
      
shahzad: sam-da-400-07n-p4n-e-------------------------------------------------------------------------------- Posted by mike on Tuesday, November 11 2008Could I get a list of error codes for this model? I have an error 25 or 52. I also have a pam to plc link lost. all other drives have no error.
Reply
    
ALEKSANDER: I have a problem with SAM DA 400-07N-P4N-E on can-bodi line SOUDRONIC.Its alarm 06XXF00E after one hour work.May I resolved this problem ?How much cost this new device?
Reply
    
Wilson Gasch Junior: Do you have some representative in Brazil? I have SAM and PAM units in my machine who needs to be repaired.I 'm waiting for your answer,Best regards,Wilson
Reply
      
Brendan: Hello;We need Socapel SAM and PAM for our machinery as spare parts. If you have or you know the source from where we can get, please let me know at my email addresss; sparesformachines@gmail.com.Would appreciate your prompt response. Thanks.
Reply
      
cesar viglianco: um socapel motorista Olá Eu tenho sam-da-400-07n PRN-em506l conectado a um nuebo motor 0r0d-0029-0 quando desistir de erro resover dá-nos acreditar que nós deve sintonizar o motor com o driver.É possível facilitar o software(ferramentas SAM)
Reply
    
Adem Ceyhaner: To Whom that may concern;We have one Socapel PAM Unit which is defecetive and gives error like 0080EE21, 0B80E002 etc.Please let me know that have ever repaired this Unit or not.I am waiting for your helpBEST REGARDSADEM CEYHANERMENDERES TEKSTIL AS TURKEY
Reply
  
Tahir Hussain: Dear,I am looking for following SERVO controllers made by DANAHER MOTION:SAM-DA-400 480-07B-P5N-G (Part # 9032012567)SAM-DA-400 480-14B-P4N-F (Part # 9032010563)Rgds, Tahir Hussain
Reply
    
mustafa colak: socapel-sam smart axis manager SAM-DA-400-50N-P4N-E SAM-DA-400-07N-P4N-ESOCAPEL POWER SUPPLY SAM-PA-400-80-ESOCAPEL-PAM PAM-P1N-H8F-AP-P V10810
Reply
      
mohamed habib: dear sir please send us the availability of inverter power socapel for welding machine for can of tin-plateTHINK YOU BSET REGARD
Reply
      
Rashidul Hasan: Dear sir,I would like to inform you that i want to purchase socapel-sam smart axis manager SAM-DA-400-50N-P4N-E 01 pcsIf you have this device pls send your Quotation or offer.Thanks Md.rashidul HasanElectrical EngineerNoman Group of industrieswww.nomangroup.comemail: rashidul@znzfab.com
Reply
        
Nisitha: I would be grateful if you could let me know the availability of scapula SAMSAM-DA-400-50N-P4N-E Nisitha Warnakulasuriya
Reply
        
Nisitha: I would be grateful if you could let me know the availability of scapula SAMSAM-DA-400-50N-P4N-E Nisitha Warnakulasuriya
Reply
      
Md.Rashidul Hasan: Dear sir,I would like to inform you that i need socapel-sam smart axis manager SAM-DA-400-50N-P4N-E Drive if this drive is your collection please inform me with price and conditionThank you very much.Md.Rashidul HasanElectrical EngineerZaber & Zubair Fabrics Ltd.mob: 01746399155,01911397522Email: rashidulhm@gmail.com rashidul@znzfab.comWeb: www.nomangroup.comSkype: rashidul
Reply
      
abid: i need a SAM-DA-400-50N-P4N-E PLEASE ADVISE IF YOU HAVE AVAILABLE AND WHATS THE PRICE OF THIS.
Reply
  
ADEM: We face with the problem that is about communication between PAM and SAM drives. We have S7-300 PLC, 1 PAM and 13 SAM Drives. During running the machine we face a error Head Communication Error(head means SAM drives for this machine) and we observed followwing error on the PAM 0B80E002,0B80E003 or 0B80E01F.We think that this problem is because of the PAM.My question is how can i repair this PAM and Where i buy PAM from.please respond us as soon as possible
Reply
  
David Stanton: I have a Socapel 25-310 ac drive that is giving us a #6 fault code on the display and we do not have a listing for that fault.
Reply
  
TaceCertieree: Hello, i newbie, anybody can help me?
Reply
  
Addiniamync: I need a driver for my phillips snn6500 wireless netcardor smc2632 wireless net cardI can t make them run on linpus linux liteplease helpregardsAddiniamync
Reply
  
Leo: With have a problem wiht the sam, tha alar is 2t, corresponding in the manual a problem with the temperature in the motor, but also say wit is posible tha sam is bad. I change the unit and program and continue with the sim error, what is your oppinion, thanks
Reply
  
JACKELINE: SERVO SOCAPEL AMPLIFIER ST1 80 310 YNO 9032011677
Reply
  
hussnain: i want to take "sam drive " to running condition without connecting pam.please help me Thanks hussnain
Reply
  
jaswant: dear sir servo drive manual sam-da-400-07 n-p4n- e modal . tests& services ,repairs manual pdf file Please sand my email address. Thanks.
Reply
  
Wasim Abbas: Dear Concern, Please see under below detail then quote rate and also share performa invoice now on first priority.1)SAM-DA-400 480-07N-P4N-E 06 PcsI’m waiting your Quick and positive reply
Reply
Mustafa Çolak: i have a socapel sam-da07 unit to sell
Reply
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z