We repair a wide range of K.E.W. Equipment.
Ask questions, or call 1-336-969-0110 for faster service.
Use the search bar above to find specific manufacturers.
Josh Campbell: I am trying to refurbish a kew 1502v-66 power washer. I cannot get the oil fired burner to kick on. The control panel has a digital temp gauge and it shows the temperature of the water at its maximum value when the water is cold. I am in question if this is the problem with the burner not firing. I am interested in any electrical diagrams, service manuals, or tech suggestions that you have. Thanks, Josh.
Reply
lyndon hammill: All the lights on the temp gauge lit means that the fuel tankis empty. If there is fuel in the tank, there may not be enoughto activate the tank sensor. put more fuel in.If the tank is full,the tank sender is faulty. It will need replacing.In the meentime you can bypass the tank sender by shorting out the two wires. Follow the cable up from the diesel tank up to the circuitboard inside the electrics box.cut the two wires that go to the circuit board and strip of insulation. Twist these wires togetherand this should solve the problem. If not, Either the board isknackered or the temperature sensor is knakered. The temperature sensor is located underneath the boiler on the water outlet andshould have a red wire coming of it up to the circuit board.Remove these 2 wires from the curcuit board and measure theresistance between these wires.It should measure around 500 ohmsat room temperatre. If not it requires replacing.You can Temporaryiliybypass the temperature sensor by repacing it with a 500 ohms resistor,any problems or if you need any parts email me regards.
Reply
ken Tucker: My KEW 1502v-66 is smoking badly and does not get hot. I think the diesel is not burning right. There is a blue flame between the contacts.
Reply
mark: clean out the disel jet, clean out fillter under the fan, make sure u have good tight flexi hose connection, good luck
Reply
thomas thorn: The temprature regulator on the top of the washer is broken off next to the gauge i need a new part
Reply
sandy stevens: Is there anyway to get a takedown of the pump on my kew steam cleaner the model # 08022-56? A parts book would be good.
Reply
Scott A Wilson I: Hi there.I have A Kew steam cleaner model #0802v-56 And would like to see about getting these manual 's for this cleaner . Please and thank you . Scott
Reply
Richard Lane: HelloI have a kew 1502 steam cleaner which has a problem with the burner. It will run for about 5 seconds then cut out, I have changed the diesel filter and cleaned the filter into the nozzle. Also I have checked that the electrodes are working properly. Its as if something is turning the diesel supply off. Do you have any ideas? Also can you supply pump seal kits and how much are these?Many thanks Richard
Reply
Dale: Hi, put a oring kit in pump an still get only tap pressure everything looks good ,keyway on pump motor fine. any ideas. Thanks,
Reply
m j cars: when i turn the machine on it trips the electrick
Reply
Anthony blair rowland: Please can you help i have a kew 1502v it will run fine cold, as soon as i demand heat it runs for 5 seconds and switches off if you switch it on & off,it runs for 5seconds and it will do this all day. what is the solution please
Reply
ali: I 'm looking for the maintenance manual for this machine
Reply
Jesus: Hi I have a KEW 1502v and some body stolen parts so I put all back together but for any reason it not working the heater and I suspected it about the wiring position, and the pressure is stopping and not keep spraying and some times work fine but some times not, one time I fix only with a new clamp in the feeder line from the tank to the pump and now I put a new hose and clamps but still the same
Reply
MARK: My kew steam cleaner does not have water pressure. It exits the gun but only trickles out. Can you help? Many thanksMark
Reply
Hassan Mortazavi: i just got a used ke w scorpian steam cleaner and everything works exept it does not ignite or no spark to get flame.any idea.thankshassan
Reply
Hassan. Mortazavi: How do i test the electrod or egniter to see its good?Thanks
Reply
Adrian Frost: Hi, I have a KEW Steam Cleaner model 16A2V-66 Year 1986. I bought it from a company asset auction and never saw it working. I have now tried to use it and the temperature lights reached the temperature set once, then the burner went out and would not re-light. I dissconnected the fuel supply to the burner and no fuel was leaving the Danfoss pump. I had a full tank of fuel and checked the supply voltage to the solenoid of the Danfoss fuel pump and with the switch set to the the burner on position, there was no voltage going to the coil to open the outlet port of the pump. Please could anyone tell me what the safety systems are on this unit and what could stop the printed circuit board sending the voltage to open the solenoid valve of the pump to supply the fuel to the burner ?Thank you for your time.
Reply
Hartono: Dear AllPlease give me the information about Services center KEW 0901V In indonesia , for your best cooperation i would to say many thanks
Reply
ken williams: Hi would you have a service manual for this cleaner??
Reply
leo: DO YOU HAVE A SOLUTION FOR THE OIL VALVE FROM THE BURNERIT WILL NOT GO ON BY WORKING WITH THE MACHINEPRESSION KONTAKTS ARE OKE
Reply
Kevin Gonneau: Looking for parts manual of help with parts for Unit Model #3803V-103 1985 40No.# 2104067 240v 1 30 ampAny help would be greatly appreciated.
Reply
Blair: call windy city equipment located in Elgin, Illinois
Reply
Raymond Cooper: I need a service manual for a KEW 4503KB with exploded views, parts lists with prices... thank you for your time and help with this problem..Raymond Cooper951-926-5394
Reply
Joe Duran: Can I find a manual ?I was given one of these to me by a customer. I think I need a special water hose??
Reply
Bob Schultz III: I need a service manual with part numbers and specifacation please.
Reply
mark: hi could you tell me where I would get service manual for kew 1640hathanks mark
Reply
mario yasin: i need to fix my pei kew 4503kb pumbe kit and throtecan you fix itthank you
Reply
gary case: we can 't get water flow through the machine
Reply
Antonio Gonzalez: need the service manual of KEW 01K pressure washer
Reply
Six B Construction: I need a operation manuel for K.E.W. 3803V-103
Reply
Rudy Martens: I need a operation manual for KEW 1502v-66
Reply
Carolyn S. Valdivia: KEW 3803V-103 fuel pump is not delivering to the burner. Please either send a manual or advise. I will call for technical assistance 6 23 2011Thank you Carolyn S. ValdiviaJackson Drop Storage YardTruck & Trailer Repair517-795-1353
Reply
Brent C.: No fuel getting to burner, need manual for test procedure. Thank you, Brent C.
Reply
BoΕΎe Gudelj: KEW 1502 V-66 user manual , service manual
Reply
maria helena: i need manual for kew 1640ha
Reply
Amin: I have Kew 1640h i need operating manual,
Reply
cindy janeski: I am looking for a shop that carries replacement parts for a KEW pressure washer, the hose has sprung a leak and need to replace it the spray nozzle is also attached to the hose as a all in one unit
Reply
reidar kvalvik: Hi.I need reper manual for KEW royalBest regards Reidar Kvalvik
Reply
marcondes: my machine stop work hot water and pressure no good work
Reply
Owen Torgerson: Great machine, had since new, recently experiencing difficulties acquiring heat.Lots of kerosene, lots of pressure on cold, new fuel spray nozzle...Help
Reply
EdwardKn: Hello. And Bye.
Reply
dan johnson: I am trying to find out any info on this Kew (0802v-56)steam washer. If someone has a manual available, that would be great.
Reply
steve oiveros: I need a parts schematic so I could repair the pump I need the seals kit.
Reply
steve oliveros: i need a parts list so i could repair the pump
Reply
JAMES FARMER: the fuel will not pump, I don t have the voltage coming out of the oil area of the board to open the solenoid on the fuel pump. I need a schematic to trace the problem, is there one available ?
Reply
KEIRON: my steam cleaner is flashing F1 light, does anyone know what this fault is and does anyone have a manuel for this model?many thanks
Reply
REYGAN: my steam cleaner 1640h is showing alarm F1 could anybody help me to find out the reason or send me manual of this machine thanksreygan bernard
Reply
jonas hofer: I need an instruction manual for a KEW 1640H When i put power to it, it just shut 's off after two seconds, and i have to reset it. A sign in the small screen say 's, P1 and F1 i don 't know what they mean.
Reply
hans: i can 't get pressure on my kew 1640H. But i have seen that there are watercristals in the pressuremeter. Does someone know what the problem is?Thanks
Reply
swordcrown sevices: we have a KEW steam cleaner,not sure of age,trolley mounted, recent purchase, but not working.is there anybody out there who can help us, with regards to diagrams, or any possible imformation, perhaps we can then decide on further age, model etc , your help would be greatly appreciated.Yours sincerely
Reply
larry: need to find out how to change the unit from 110 volts to 220 volts. thanks
Reply
PAUL GALLAGHER: HI,I HAVE JUST PURCHASED A KEW 38A2VA POWER WASHER. IS IT POSSIBLE TO GET A MANUAL FOR THIS MACHINE? ALSO WHAT GOES IN THE TANK MARKED WITH A SNOWFLAKE?THANKS PAUL.
Reply
Martin Ferguson: No comments
Reply
thijs thissen: We have recently purchased an second hand KEW high pressure cleaner but it does not get the full cleaning pressure. Can I recieve an owners manual by email to see what parts may be broekn in order to fix the machine?Thank you in advance.best regards,Thijs.
Reply
Bodengien: HelloBought a secand hand KEW38A2VA and overhauld and cleanend the machine. The boiler doesnt start however. Can I get a manual for the machine ?? Thanks in advance. Bodengien.
Reply
Gary: The burner won 't turn off can anyone help
Reply
Chris bolton: My Kew is not building up pressure can you tell me why please
Reply
TOBY ANDERSON: I have a kew alto 2340ha Everything was working and the usint up and quit It showed a 0 flashing and I unplougged it and put it back it reset to solid 0 but when you push the power on it does nothing. I let sit unplugged but nothing works now. Is there anyone who works on these anymore I am in Wisconsin and I realize it is outdated but I spent thousands of dollars on this unit. Now im stuck Any suggestions ?
Reply
Tom Duclos: Need transformer for above unit part number #3819901 can you help me..
Reply
angelineadlecraft@gmail.com: Good dayI am trying to find a manual to assist me with the heating system of a K.E.W. 38A2VA.Many thanks
Reply
Gerald Mansfield: I purchased a K.E.W. 1500 unit on a sale and would like to get an owners manual service manual for it. It 's an electric unit. Thank you, Gerry Mansfield
Reply
gary appleton: i need new hose
Reply
David Kerr: Hi, Help please, i 'm in need of a new lance for my older Kew Hobby 2600, would you have this item in stock ?
Reply
Jeff Osborn: I have recently acquired a K.E.W. Pressure washer and am trying to find information about it. It appears to be from Denmark and in the Model box it just says Hobby. Another box on the ID plate says 62 bar. The gauge on the machine reads 0 to 150 and on the face of the dial it says X 1000. THAT WOULD BE A LOT OF PRESSURE! Let me know if you can help.
Reply
Tom Hamilton: I may have the same pressure washer you have. My pressure gauge shows two circular pressure scales. The outer scale is from 0 to 150 with a heavy mark at the 50 digit and 100 digit. At the bottom it says "BAR ". If your information plate says 62 BAR as mine does then acceptable pressure is between 50 and 100 BAR. The inner scale is in PSI is shows a heavy mark at 1 and another at 2 which I take to be the normal range as well. It also says x 1000 psi. So, in my case the inner scale is in PSI. When my pressure washer is running (I 'm going from memory here) it seems to put out around 1000 PSI. Also, my KEW Hobby has a way to check the oil in the compressor at the top near the gauge. I have to pry the dipstick out with my finger nail, but that 's OK by me. It thankfully says "Full ". On the ID plate I 've got a build date of 1986 33 which I take to be the 33 week of 1986. The ID plate also says 100 BAR (which may be the maximum pressure) and a flow rate of 8.6 l min. This was my Dad 's pressure washer which I got from him. It still works after all these years although the rubber covering is peeling off the pressure hose exposing the white layer underneath. Good luck with yours.
Reply
J.den Dekker: Geachte meneer mevrouw,Ik heb heb kew 1500 hogedruk spuitpart nr. 6137219 Serial nr. 6998760.Kunt u mij vertellen of ik een terrascleaner kan krijgen voor deze hogedruk spuit en als dat mogelijk is kunt u mij vertellen waar en wat hij kost.vr.gr.J.den Dekker
Reply
Ruth Montefiore: The black hose pipe connected to this pressure washer has a whole in it. Can it be repaired and if so how please. If not how much will it cost to desptach a replacement to me or where can I purchase this hose pipe? Is it something I can obtain from a builders merchants and if so what size please?I look forward to hearing from you as soon as possible please so that I can complete cleaning my patio.Thank you
Reply
AUSTIN GIBBONS: CAN I BUY A SPARE PART FOR THE ABOVE, IE, THE PRESSURE WASHER AT THE END OF THE LANCE.?WITH THANKS AUSTIN GIBBONS
Reply
Odyssey Winery: I have a KEW pressure washer, model 0840HA. I am receiving intermittant F2 error codes and C4 error codes. I have taken it into my dealer for "repair " however the problem continues. Any ideas?
Reply
john farkas: I am looking a the circuit board for my 0840HA hot water pressure washer. Mine burned out, the rest of the machine is nearly new. It would be a shame to trash it. KEW no longer makes this board.
Reply
john farkas: For any KEW products call Chris Gerber in S.C. (877)322-2586. Very knowledgable and helpfull. He is the US service rep.
Reply
holmeside garage lee scott: i have a kew 1640ha which i am having a bit trouble with reacently when whent to use it it cum up with the fault L1 and now the machine will not start,i was wundering if you could give me a bit help THANKS
Reply
mohammed zaki: HelloPlease can you inform me where i can repair my washing machinemodel (5203k) in united arab emitares.Thanks @ Best Regards
Reply
dan lucas: hi i brought this k.e.w h1500 steam cleaner some year ago,i put it away after it was working ok over 12month ago.i lent it to my brother and it will not pressure up.....his any one out there i can ring to get parts so i can fix it thx 07779666678
Reply
Stuart: I need a service manual for a KEW 1502-66 with exploded views, parts lists with prices... thank you for your time and help with this problem..
Reply
SHABAN LIMANI: guten abent icsh bin ljimani cshaban aus macedonia tetovo icsh brauche eine pumpe for choch druck for kew 1502und kene cshiken in macedonia und kenen preis ceigen bite und in duetsh ich veis bite und in meine email cshriben bite filen dank fur das
Reply
LIMANI: guten abent icsh bin limani cshaban aus macedonia icsh brauche eine tail for meine macshine das chaist pumpe for k.e.w.1502 iat mit drei klipen un federen und kenzi zaigen prais bite
Reply
Murray Smith: I need a instruction manual for a KEW 1502-66 thank you
Reply
shaban limani : JA ICSH BIN LIMANI CSHABAN ICSH BRAUCHE EINE PUMP MACSHINE FOR AUTO VACSH MACSHINE IST FOR MARKE K.E.W 1502V ICSH CHAP MACSHINE ABER PUMP IST KAPUT BITEIN MAINE EMAIL CSHIKENSI DI VORT FOR MAINE RESPEKT
Reply
Arvid Hartsuiker: Front seal on pump leaking, looking for parts to repair and repair manual. Please give me a call or email. Thanks Arvid
Reply
William Knee: HI I check all and no start and I am a Electrician
Reply
Garry S James: I have a KEW 1502V β Hot & Cold Pressure Washer. I will be running this of a Generator at the same time as a water pump which has a rating of 700w.1. Can you what is the start up current of the Pressure Washer.2. What size Generator should I be looking for to run the Pressure Water and the Water Pump (700w) at the same time.2. Can you provide a manual for the Pressure Washer, if so how much?GSJ
Reply
Len: I have a copy of the users instruction book for this machine if you are still in need.
Reply
Clifford Brown: I still do not have all the details of what this machine is, but it appears to be a hot water pressure washer.. Would be interested in the instructions manual to see if I can get it going. Do not have all of the ID place numbers copied down yet though. The copper windings for the boiler look good from what I can see through the top openings. Do not know what I need yet to get this thing working, the plug has been taken off of it for some reason. Only date tagging is a sticker that says 75th Anniversary on it and a year. That would make it about 15 years ago if I look again at it to verify the date. Would appreciate any and all feed back you can give me and how much you want for the manual or a copy of it. Cliff
Reply
Richard Beck: Have a Kew 3803V pressure washer, need to know where I can get itrepaired nearby.thank you
Reply
Tim: I am looking for a seal kit for the pump on this unit if you can get one please email me back.
Reply
brian breslin: where might I download a user manual for parts and maintenance of my 1640h Thanks Brian
Reply
Ola Wikstrand: HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks! Ola
Reply
Serge: HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks!
Reply
Ulf Dahl: HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks!Uffe
Reply
Ron: My coil froze last winer when heater broke in shop over weekend , do you have any coils
Reply
frank welch: just want to know how old this machine is and if it can still be repaired,i have no knowledge of what year it was made and know of no place to get it repaired
Reply
Grant Neeley: I have a KEW 23A2V pressure washer that the boiler Coil is completely shot now. I have welded some hole back together, but now it is beyond repair. Does anyone know where I can get a replacement coil?
Reply
ryan: I have a 1979 kew power washer and am looking for some pump parts or info on where to get parts it is mostly all in good shape put the pump needs work any info would be greatly apresated thanks ryan
Reply
CESAR ALCAZAR: Hi I have a Heated Pressure Washer, and Im lookin for a specific part can you tell me if ispossible to found it. Lelow information of the machineMAKER: KEWMODELL: 3803V-103SER:2103205ASSET:43-1-5
Reply