We repair a wide range of Anilam Equipment.
Ask questions, or call 1-336-969-0110 for faster service.
Use the search bar above to find specific manufacturers.
Scott Redfern: One of the PCB boards in the controller came off it 's mountings during transport and was damaged. The servos do not power up and the release for Spindle operation is not enabled (even in Spindle manual). Do you need the electrical schematics that I have to make the repair?
Reply
David: we got a new cnc lathe in our shope with an anilam crusader II control but if we try to jog the axis in manual mode you get an error code 18 we know what the book says about it but we do not know what to do to fix it any help would be greatly appreciatedThanks,David
Reply
christopher atwan: Did you reset the unit before you tried to jog it? Does it move at all before the error 18 code shows up?Christopher Atwan
Reply
rasheed: sorry i have softlimit problem but do not know how to remove
Reply
JOSE PRADA: We have an Anilam machine that is died.The screen show +x or -x limit. Can you help me?...Thanks..
Reply
marc snel: i have a milling machine with a anilam crusader when i start up the machine he gives a error 18 after 3 seconds and the x as moves 0.5 mm the machine have indramat servos please can you help me
Reply
muhammad amin: Dear SirHow we adjust the backlash in machinethanksAMIN
Reply
OMAR AZHAR RANA: I have a Anilam Crusader II on my Milling Machine not working plz help me to know weather I can Retrofit an other unit with minimun change in parts and also tell me where I can get a complete Repair Manually of this THANKS OMAR AZHAR RANA
Reply
Minhas: Mr.Umer Azhar Rana We are in pakistan and we have all of Anilam Cursader II Help tell me in detail what condition of your,s Control You can replay below minhas1986@gmail.com
Reply
RANJIT SINGH: WE NEED ELECTRICAL CIRCUIT DIAGRAM+REPAIRING MANUAL FOR ANILAM CRUSADER-2(3-AXIS).WHAT WILL BE THE CHARGES FOR THE SAME.
Reply
John Klingaman: I have an Anilam 1100 control that wont keep the cmos settings. The control starts to boot up but then tells me to push F2 to enter setup. I enter setup then save the changes but when I reboot the control does the same thing. What can be done to fix my problem?
Reply
steve wood: Hi john I called you earlier about connectors for servo driver card. We had cmos setting problems and fixed them on the 1100 by replacing the cpu board bios chip which contains internal batteries. We can walk you throughit if you need help. Interesting how your post about this problem poppedup in front of me while looking for more info on the 1100.
Reply
Muhammad Javed: Daer Sir,We are working on Anilam Since 4 years. We made many mould on it and machine working quality is good. So that is why we purchase one more Anilam 1100 machine from a old machinery ware house. but machine have no software, can you plz send us Anilam 1100 s software ver1.66. we will be very thank full to you.
Reply
piyush: i have anilam 1100 control with bridge port i have change Battery but now i have start machine y axis go to Negative direction and message Y axis lag over.
Reply
Gerald Hamilton: When I booted machine COMS battery state lowStandard COMS setupAdvance COMS setupauto configuration with BIOS defaultsauto configuration with power on defaultschange passwordauto detect hard diskauto detect hard disk utilitywrite to COMS and exitdonot write to COMS and exitI dont know where batteries are located or what to do here any help would be appricated
Reply
chuck green: 1100m on a bridgeport style knee mill,i was told the mother board is out. anyway to check it and how much would a replacement board cost.
Reply
Gary Boomgarden: We have a bridgeport with the 1100 anilam control on it. About a year ago the feed on the x @ y stopped working. Not able to engage the servos. We had a repairman come in who told us that the board that controls the servos is out. Have been waiting for him to have this repaired but has not found anyone to repair it. Can you help or recommend someone or someplace to have this repaired or replaced.
Reply
John Steimer: We have not used the machine with the Anilam SR1100 for several years.Replaced the battery and tried to reload the software but get the following message: Bad or Missing Shell ( command.com).I assume the discs have degraded.If you agree how do I get a new set of discs?Disk: 1100 M 2AXVer: 6.22A:use w frmw Ver .72LDisk: 1100 M DiagVer:3.09Thanks in advance.John
Reply
Richard S. Heckman Sr.: The Z axis is inoperative, manual movement of the Z axis results in the power contactor tripping out. This is the same contactor that is controlled by the limit switches. When the machine is first powered up the Y,X servo motors are powered, the Z is not getting power.
Reply
K PRABHAKARA RAO: DEAR SIRORDNANCE FACTORY, MINISTRY OF DEFENCE, TIRUCHIRAPALLI- 620 016, (TAMILNADU STATE), SEARCHING FOR CNC SYSTEM AND DRIVE SERVICING AGENCY, WHO CAN REPAIR KIRLOSKAR CRUSADER MARK-II SYSTEM FITTED ON BFW VERTICAL MILLING MACHINE . KINDLY INTIMATE THE FEASIBILITY OF REAPAIRS OF THE SAME AT YOUR WORKS PLEASE. THIS IS BEING ISSUED WITHOUT ANY FINANCIAL COMMITMENT ON EITHER SIDE AT THIS STAGE PLEASE.REGRADS,
Reply
abdoaakl: i need the Anilam Anilam Crusader II wiring Diagramabdoaakl-cairo - egypt-abdoaakl1@yahoo.comthanks for you.
Reply
chris hendricks: i need servo Y servo wiring diagram
Reply
trammel rushing: where does the R5232 connect to
Reply
Russell Bilby: hello, i have a cruasder m controller that has a broken membrane face where you push the program buttons. can you supply a new or good used one?and for what price, thanks Russell
Reply
Michael James: Russell,I may know where theres a used control "head " with a functional touch pad membrane. I sold one to a friend several years ago and I believe he never used it. Email me at drembedded_AT_yahoo_DOT_com with your contact info.Cheers,Michael
Reply
Jose Maldonado: Hi I has a problem with a Lagun CNC with control anilam cruzader II I would like to buy the manual first and then expaint to you whats is our problem
Reply
Ranjit Singh: Hi,I have a Arnault Samua machine ZXV1 which is fitted with Anilam Crusador 2 controller and Indramat TRM2 DC servo drives. When the machine is switched on , the controller displays ERROR CODE 12. and I am not able to enter anything. It is not accepting any command. I tried pressin Deelte Event button but it also dint lead to anything.Can you please help me with this??It will be really great.Thanks in advanceRanjit Singh
Reply
carlos: I am sorry to hear that you are experiencing issues with your Anilam 501 901-159 circuit board. Can you please provide more details about the problem you are facing with the unit? Specifically, have you noticed any specific functionality that is not working as expected, such as error codes or malfunctions during operation? Understanding the exact symptoms will help in diagnosing the issue accurately. In terms of repair services, the estimated replacement cost for a circuit board for an Anilam 501 901-159 unit can vary depending on the extent of the damage and the specific parts that need to be replaced. It is recommended to reach out to a qualified technician or repair service provider for a detailed assessment and cost estimate before proceeding with any repairs.
Reply