K.E.W Service & Repair Forum

the fuel will not pump, I don`t have the voltage coming out of the oil area of the board to open the solenoid on the fuel pump. I need a schematic to trace the problem, is there one available ?

β€” Posted by JAMES FARMER on 2016-05-02

ReplyπŸ—¨οΈAsk a New Question Below❓


Recent Comments Search: "K.E.W"

If you need your K.E.W unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110


Recent 95 Comments

#K.E.W by Clifford Brown on 2010-10-10 03:46
I still do not have all the details of what this machine is, but it appears to be a hot water pressure washer.. Would be interested in the instructions manual to see if I can get it going. Do not have all of the ID place numbers copied down yet though. The copper windings for the boiler look good fr…...
Show More
#K.E.W by ali on 2009-05-31 05:45
I\'m looking for the maintenance manual for this machine
#K.E.W by Gary on 2009-06-07 19:47
The burner won\'t turn off can anyone help
#K.E.W by J.den Dekker on 2011-04-03 06:34
Geachte meneer/mevrouw,Ik heb heb kew 1500 hogedruk spuitpart nr. 6137219 Serial nr. 6998760.Kunt u mij vertellen of ik een terrascleaner kan krijgen voor deze hogedruk spuit en als dat mogelijk is kunt u mij vertellen waar en wat hij kost.vr.gr.J.den Dekker
#K.E.W by Hassan Mortazavi on 2010-10-08 16:23
i just got a used ke w scorpian steam cleaner and everything works exept it does not ignite or no spark to get flame.any idea.thankshassan
#K.E.W by Owen Torgerson on 2012-03-22 19:12
Great machine, had since new, recently experiencing difficulties acquiring heat.Lots of kerosene, lots of pressure on cold, new fuel spray nozzle...Help
#K.E.W by hans on 2009-05-13 16:54
i can\'t get pressure on my kew 1640H. But i have seen that there are watercristals in the pressuremeter. Does someone know what the problem is?Thanks
#K.E.W by ken Tucker on 2008-05-01 16:53
My KEW 1502v-66 is smoking badly and does not get hot. I think the diesel is not burning right. There is a blue flame between the contacts.
#K.E.W by brian breslin on 2009-10-14 19:43
where might I download a user manual for parts and maintenance of my 1640h Thanks Brian
#K.E.W by Ulf Dahl on 2015-03-24 13:14
HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks!Uffe
#K.E.W by mark on 2014-10-21 13:50
hi could you tell me where I would get service manual for kew 1640hathanks mark
#K.E.W by thomas thorn on 2009-05-03 09:24
The temprature regulator on the top of the washer is broken off next to the gauge i need a new part
#K.E.W by ken williams on 2011-11-08 03:02
Hi would you have a service manual for this cleaner??
#K.E.W by Blair on 2007-08-15 01:10
call windy city equipment located in Elgin, Illinois
#K.E.W by JAMES FARMER on 2016-05-02 19:22
the fuel will not pump, I don`t have the voltage coming out of the oil area of the board to open the solenoid on the fuel pump. I need a schematic to trace the problem, is there one available ?
#K.E.W by Kevin Gonneau on 2007-05-07 19:40
Looking for parts manual of help with parts for Unit Model #3803V-103 1985/40No.# 2104067 240v/1/30 ampAny help would be greatly appreciated.
#K.E.W by john farkas on 2011-10-26 18:47
For any KEW products call Chris Gerber in S.C. (877)322-2586. Very knowledgable and helpfull. He is the US service rep.
#K.E.W by Richard Lane on 2008-12-24 11:32
HelloI have a kew 1502 steam cleaner which has a problem with the burner. It will run for about 5 seconds then cut out, I have changed the diesel filter and cleaned the filter into the nozzle. Also I have checked that the electrodes are working properly. Its as if something is turning the diesel sup…...
Show More
#K.E.W by Ruth Montefiore on 2010-03-15 13:33
The black hose pipe connected to this pressure washer has a whole in it. Can it be repaired and if so how please. If not how much will it cost to desptach a replacement to me or where can I purchase this hose pipe? Is it something I can obtain from a builders merchants and if so what size please?I l…...
Show More
#K.E.W by David Kerr on 2009-06-12 19:28
Hi, Help please, i\'m in need of a new lance for my older Kew Hobby 2600, would you have this item in stock ?
#K.E.W by Six B Construction on 2008-10-02 15:28
I need a operation manuel for K.E.W. 3803V-103
#K.E.W by Carolyn S. Valdivia on 2011-06-22 21:16
KEW 3803V-103 fuel pump is not delivering to the burner. Please either send a manual or advise. I will call for technical assistance 6/23/2011Thank you Carolyn S. ValdiviaJackson Drop Storage YardTruck & Trailer Repair517-795-1353
#K.E.W by mario yasin on 2012-12-04 21:44
i need to fix my pei kew 4503kb pumbe kit and throtecan you fix itthank you
#K.E.W by steve oliveros on 2011-06-24 22:12
i need a parts list so i could repair the pump
#K.E.W by marcondes on 2010-03-17 22:11
my machine stop work hot water and pressure no good work
#K.E.W by leo on 2012-10-14 09:11
DO YOU HAVE A SOLUTION FOR THE OIL VALVE FROM THE BURNERIT WILL NOT GO ON BY WORKING WITH THE MACHINEPRESSION KONTAKTS ARE OKE
#K.E.W by Tom Hamilton on 2009-12-16 22:16
I may have the same pressure washer you have. My pressure gauge shows two circular pressure scales. The outer scale is from 0 to 150 with a heavy mark at the 50 digit and 100 digit. At the bottom it says \"BAR\". If your information plate says 62 BAR as mine does then acceptable pressure is between …...
Show More
#K.E.W by EdwardKn on 2015-03-27 17:20
Hello. And Bye.
#K.E.W by gary case on 2010-09-23 15:00
we can\'t get water flow through the machine
#K.E.W by KEIRON on 2008-04-03 18:18
my steam cleaner is flashing F1 light, does anyone know what this fault is and does anyone have a manuel for this model?many thanks
#K.E.W by Hartono on 2011-10-19 06:46
Dear AllPlease give me the information about Services center KEW 0901V In indonesia , for your best cooperation i would to say many thanks
#K.E.W by gary appleton on 2008-06-10 15:53
i need new hose
#K.E.W by TOBY ANDERSON on 2014-08-15 17:47
I have a kew alto 2340ha Everything was working and the usint up and quit It showed a 0 flashing and I unplougged it and put it back it reset to solid 0 but when you push the power on it does nothing. I let sit unplugged but nothing works now. Is there anyone who works on these anymore I am in Wisco…...
Show More
#K.E.W by Tom Duclos on 2016-05-31 14:22
Need transformer for above unit part number #3819901 can you help me..
#K.E.W by AUSTIN GIBBONS on 2010-03-30 14:40
CAN I BUY A SPARE PART FOR THE ABOVE, IE, THE PRESSURE WASHER AT THE END OF THE LANCE.?WITH THANKS AUSTIN GIBBONS
#K.E.W by Ron on 2010-10-12 02:52
My coil froze last winer when heater broke in shop over weekend , do you have any coils
#K.E.W by Jeff Osborn on 2009-11-23 21:46
I have recently acquired a K.E.W. Pressure washer and am trying to find information about it. It appears to be from Denmark and in the Model box it just says Hobby. Another box on the ID plate says 62 bar. The gauge on the machine reads 0 to 150 and on the face of the dial it says X 1000. THAT WOULD…...
Show More
#K.E.W by Len on 2009-10-23 14:28
I have a copy of the users instruction book for this machine if you are still in need.
#K.E.W by john farkas on 2011-10-26 18:38
I am looking a the circuit board for my 0840HA hot water pressure washer. Mine burned out, the rest of the machine is nearly new. It would be a shame to trash it. KEW no longer makes this board.
#K.E.W by ryan on 2011-04-02 17:51
I have a 1979 kew power washer and am looking for some pump parts or info on where to get parts it is mostly all in good shape put the pump needs work any info would be greatly apresated thanks ryan
#K.E.W by Serge on 2013-06-13 13:06
HelloI have just purchased a KEW 38A2VA power washer with a faulty heater. Is it possible to get a manual and an exploded view drawing over this machine?Thanks!
#K.E.W by MARK on 2010-01-02 19:00
My kew steam cleaner does not have water pressure. It exits the gun but only trickles out. Can you help? Many thanksMark
#K.E.W by Arvid Hartsuiker on 2008-11-11 18:15
Front seal on pump leaking, looking for parts to repair and repair manual. Please give me a call or email. Thanks Arvid
#K.E.W by dan lucas on 2013-03-13 22:08
hi i brought this k.e.w h1500 steam cleaner some year ago,i put it away after it was working ok over 12month ago.i lent it to my brother and it will not pressure up.....his any one out there i can ring to get parts so i can fix it thx 07779666678
#K.E.W by Bob Schultz III on 2011-08-17 15:47
I need a service manual with part numbers and specifacation please.
#K.E.W by Garry S James on 2009-04-09 10:26
I have a KEW 1502V – Hot & Cold Pressure Washer. I will be running this of a Generator at the same time as a water pump which has a rating of 700w.1. Can you what is the start up current of the Pressure Washer.2. What size Generator should I be looking for to run the Pressure Water and the Water Pum…...
Show More
#K.E.W by larry on 2009-03-26 07:25
need to find out how to change the unit from 110 volts to 220 volts. thanks
#K.E.W by Bodengien on 2017-12-18 08:27
HelloBought a secand hand KEW38A2VA and overhauld and cleanend the machine. The boiler doesnt start however. Can I get a manual for the machine ?? Thanks in advance. Bodengien.
#K.E.W by Scott A Wilson I on 2012-07-24 12:43
Hi there.I have A Kew steam cleaner model #0802v-56 And would like to see about getting these manual\'s for this cleaner . Please and thank you . Scott
#K.E.W by mark on 2008-07-06 07:56
clean out the disel jet, clean out fillter under the fan, make sure u have good tight flexi hose connection, good luck

Contact Us

πŸš‘Shop LocationπŸ› οΈ

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
πŸš‘ Rush repair shipments only β€” no walk-ins.

πŸ“žPhone

1-336-969-0110

πŸ“¦Mailing AddressπŸš›

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
πŸ“¦ Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.