I have 2 remote garage door openers made by Advance Industries, Shelbyville, IN. One works very well. The other was kept in storage and the battery inside leaked and corroded the battery connector. These use a 9-volt battery. The FCC ID number is BSH8YN106546 and the MFG. number is 081587. The Freq. number is 380-BBD. I need to have this garage door opener either repaired or replaced. Please advise.Thank you so much

I have an Overhead Garage Door Opener Model 100. I am looking for a replacement receiver P/N 107224-0014.

The logic timer board was used in the Crusader C-300 and C-350 slide gate operators by McKinney Electronics/Overhead Door. I would be interested in purchasing this board if it is still available and known to be functional. Mine has the same issue as described in the iernc post by David Prevo in Oct. 2012 The time adjust control is not functioning and the gate will either close within one or two seconds, or, if slightly moved for a longer delay, will stay open and not close at all.

im looking to replace a bsh8yn229 remote

We have 2 overhead garage doors........... but no remotes. They are both Model 55A Garage Door Opener System by The Overhead Door Co. They were installed about 1985. Wondering if there are replacement remotes we can purchase anywhere.Would appreciate any information or help you could provide concerning this matter. Thank you for your time and assistance.Ann

Remote control: Crusader Solid State Model 200SS/202SS

Contact me if you still need themMiMarch 31 2015

The tag over three box relays says MFD. ADVANCE INDUSTRIES, APPLETON, WIS. with the controller model no. tagged on the circuit board. I may need a new board or repair to the board. One of the relays continues a slow click as long as the opener is plugged in to power. Please advise. Thanks.

I am looking for another or a replacement for the Touch n go (390-19mhz) remote that I now have. As far as I can tell it was from 1985 and is analog. It is for my \"Overhead Door\" garage door opener from the early 1970\'s. I would love to get another one for my wifes car. Thank you

Can you tell me if it is possible to get a replacement remote for a Touch n Go remote I purchaced in 1985. It is coded 390-19. there is an antenna model 702, ser#751015 if that helps. also the door opener is a model R80-az. Thank you

I forgot to mention the model of the door opener is R80-az It is 115volts and 60amps 1/3 hp. There is a separate antenna mod 702 ser#751015 code 390-19 Thank you

I have a touch n\'go remote garage door opener (390-19 mhz) for my overhead door garage opener and it works fine. I would love to get another one. I believe this has a date of 1985 on it and don\'t know if these are still possible to get. Any help? Thank yo

i need to replace 1 black box for a horton opener brand name - Horton easy access number on the board inside box - 107846-0001 Freq - 360 Mfg - 92 48 Fcc Id: BSH8YN107846Unable to find item on Google or EbayIs it still available? thanks dennis

I am looking for a circuit board Advanced Industries model No. 116220 D P/N 107243-0002 LOGIC TIMER

I have manual for this oard if you still need it

I would like to replace the 2 remotes controls that I have. the following information is: FCC ID: BSH8YN106546. FREQ. 360- MFG91 168.Your response by E-mail will be really appreciate.

I have this board in my gate opener and trying to find out how to hook up a coaxial receiver and a owners manual thank you

I have this board in my gate opener and need to find owner manual or just need to find out how to hook up the coaxial receiver to this board 760 252 9000

I purchased a house with a garage door opener made by advance industries . The remote will only work if you have direct line of site with opener. I have put in fresh batteries. It appears to be very old.Any suggestions would be appreciated.Thanks

do you have the light board that plugs into the 116220d timer board

Would like information on the purchase of two remote units. The main door remote unit has lable #107224-0002. The other unit was run over by the car and is unavilable. Please send info on how to purchase replacable items . Thank you Larry Freeze 302 Guava Pl Brea, Ca. 92821f

I need to purchase 2 ea. Advance Industries Garage Door OpenersFCC ID: BSH8YN213

Need a manual for a 24 volt AC power door opener, in order to hook it up

I need repair or replacement information regarding COPS board for the R-200 PN # 108939-0001 and other part numbers. Made by McKinney electronics for residential slide gate operator. Orginial part number was 940036-2 that came in a box marked overhead door company with no address. I purchased this system new in 1985 and had no trouble getting boards in miami florida in past years, but find them no longer availabe in my area.

I have a overhead garage doors opener. model 100. I am looking for a replacment remot and reciverreciver number is 107224-0014

Remote shows FCC# only the garage door opener is overhead door 450A I would like to find another spare remote.It is medium brown in color with a brown button and an ivory color button .The remote operates 2 doors and has 2 code selection modules one for each door.

I have been searching everywhere for an opener to my garage door.It is an older model manufactured by Overhead Door with a transformer attached manufactured by Advance Industries class 2 year \'92 model.If you have a solution please email me or call me at (903)819-5907.

I have two remotes and a receiver that I believe were made by Advance Industries, Shelbyville, Indiana. One of the remotes works only intermitently. I would like to repair or replace the remote or replace two remotes and the receiver unit on the Overhead Garage Door Opener. The opener works fine.I you are the company that can help the garage door opener is Mod R 802, NEC Class 2 Circuit, 25 Volt Max, 6 amp, 1/4 HP. Freq is 380-BBB, FCC ID BSH8YN-206, MFG 90226.A response by email would be helpful.Thanks

We have the circuit board listed above in our gate operator and the manual timing wheel on the board seems to be eradic as I put it to min. and the gate stays open approx 9 minutes. Before I played with it today, the gate would stay all the way open for 1 1/2 seconds before closing.Any suggestions?

I HAVE A KEW 16 40 HA, AND IM HAVING PROBLEMS TRYING TO FIX IT!IT WONT RUN AT ALL,THOUGHT IT MIGHT BE THE COIL , CHECKED THE WIERING! AND STILL NOTHING? HELPMANY THANKS MICHAEL

I work for Overhead Door Company of Las Cruces and we have the logic timer board in stock, but nobody hear seems to know what it goes into. We assume it\'s for a gate operator but we don\'t lnow which model> I believe it maybe for several different models.Can you help?Thanks

COULD YOU POINT ME IN THE RIGHT DIRECTION FOR A MANUAL FOR A 116220D? I;M TRYING TO DISABLE THE TIMER OR ADD PHOTO EYES.

Please contact me asap about my board repair, I thank it was shiped on friday, thats what i need to know. Thank you Bret Moore

Need logic board 116220DModel 107243-0002Do you have that availableLeonce Collins504-722-4729

Dear Sir/Madam,I am looking for a part that you have in store. That is part model no. 116220 D. I would like to know how much this part will cost me.I am looking forward for a reply.yours sincerly, Nando Semeleer.

Hi,I am in desparate need of a wiring diagram for an Advance industries 116220D board for a Mckinney Electronics operator. We need to add a reflective detector and the board we have does not have a labelled terminal block. We would appreciate any information you might have.Thanks,DeeAnne