my SYBRON-TAYLORhas stopped recording the correct speed--at low wind speed the indicator wiggles only a small amount---at high wind speed it moves only slightly up the scale---the cups seem to rotate at different speeds ie as the wind builds to higer speeds the cups rotate faster---as best i can tell like they always have for the last 30 years(ie the unit doesn\'t owe me anything)-----is there anything i can check/repair short of sending the unit to you or buying a new indicator???? i have checked the flow of current between all connections--seems OK but i don\'t know what it should be??? my ACV lowest seting is 10---meter shows nothing????-----hope you can give me some good advice---thank you in advance for whatever you can suggest----bruce cunningham

The weathervane rod bent due to some unknown reason and when I took off the top I noticed the vectical shaft was also worn very bad. Do you sell the whole package that sits on top of the roof? The machine was in for repair back in 12/17/82, bought in Sept of 73. Rough weather up here near Rochester, NY where Taylor Instreuments was born. Thank you,James S. Chatfield

I would like to know if I can purchase the roof unit ( wind/speed indicator and wire )for the 3108 Weatherscope or if I can use a different/more current model that will work as well. I was given the Weatherscope, but I cannot access the weather/wind vane at this time. Thanks, any other info. on this unit would be most appreciated ( Manuals, etc.)David Watson

we are looking for parts that go from the back of our barameter to the tower. it is a old unit. The only thing I see on it is model E weatherscope by Taylor. It is a wind guage, wind direction, temp and barameter. Thanks for your help. Darren

David,I too have become the owner of an older 3108c Weatherstation. I was fortunate enough to get the instruction booklet with it, but like you, I have no roof unit to feed it a signal.I\'ve looked around the Internet to no avail and wondered if you ever found a source for one?Thanks in advance for any help you can provide.Jeff

After reading your comments about your sensor, I realized the magnet may be one of the culprits on this issue. Over time moisture accumulates in the magnet and may weaken the field to the induction coil. The induction coil in the Taylor anemometer heads are often weakened by time - temp changes etc. 30+ yrs of use. The coil end braids come undone, but yours is still reading out. There are also two capacitors in the back of the meter and they sometimes lose charge during wind lulls. There are also two adjusting potentiometers in the back of the meter. These can calibrate the windspeed. I find taking a small 6v battery sometimes fills the capacitors back to full thus making the windspeed work again. Just make sure if you do this, to do it momentarily and without the generator unit attached. The Taylor also has a rubber piece in the center of the magnet, make sure it isn\'t rubbing the bearing plate, it slows the cup operation. You might want to consider a set screw in the outer cup hub, Taylor windspeed generators have a tendency to blow off during windstorms. I have had several 3107s. They are quite accurate if maintained. -Matt

I am looking for the anamometer cups of the above Taylor weatherscope. One of the cups broke in transit and I need a replacement for only the three cup assembly...not thr bottom sender..However,if I have to purchase the entire assembly I would gladly do so.Thank you,Ray Orobona

I have a Weatherscope by Taylor and the temperature probe is intact and works great, but the wind speed/direction thingie is gone. I have plentry of wire - nothing to connect it to.Can you help me find a new wind thingie?Sam

Have an old? Taylor Weatherscope (cannot find a Model Number) made by Taylor Instrument Company Rochester USA. Has four separate gauges - Max/Min temperature, Barometer,wind speed and wind direction set in a solid wooden cabinet. Cable linking weathervane and wind speed indicator to instruments has been cut. Can you help re rewiring. Can you help re vintage and history of the instrument.Many thanksLeo

Hi Jeff I, also have a Taylor Weatherscope. I\'m missing the Anemometer & Wind Direction unit. Can you PDF the Booklet that came with your unit? Thank you for your time. Bill of Magic Lantern Productions........Cheers !

Re; Taylor Model 3108A repair person at my home has severly damaged my external thermometer prob/bulb and has also severed the 5-strand ribbon cable which connects the wind-speed/direction unit to the main guage panel. Are there any replacement prob/bulbs and ribbon cables? Is there a 5-pin connector which could be crimped to each cable end to permit reconnection? I am concerned about weather effects on any repair, too.Thank you for any guidance you can offer.Tom Vogelpohl513-232-0356

I have the same thing as Leo. My Dad was a weatherman for the County and I inherited this. I would love to use it but I know nothing about wiring. My cable linking the weatervane and wind speed is also cut. There is a very long wire with a metal rod on the end..not sure what that is for. Can anyone give me any information? I\'m not mechanical but I willing to learn.Thanks Deb

I have a complete station that was purchased new in 1976 and never used. Is there a market for such an item?

I would be extremely interested in your weaterscope if you still have it. I had one and would love to have a replacement for it.....Bill

Hello, Is it possible to purshase a weatherscope or the entire roof mount with the speed and wind direction?Best Regards,John Tucker

Do you sell, or tell me where I can get parts.Thank you

I have a NOS Weatherscope 3108 new in the original box. Has never been unpacked or installed.I would like to sell the whole unit. Will take offers.Tom

need to replace entire speed cup assembly that fits on shaft.please, advise.

Hi:I am trying to repair/replace my Weatherscope but I do not know what a 3108 looks like. Mine is in a chery case and has 4 guages; Barometer, Thermostat, Wind Speed, and Wind Direction.Thanks - TomR

How do I contact you to discuss purchase? I am interestedthanks - TomR - 215.589.0686

Do you have a speed cup for a 3108C assembly or do I have to buy the total roof replacement?Thank you.

Hello:I have acquired a Weatherscope by Taylor (wooden box with 4 gauges) Brand new, never used. It has all the parts except the wind vane for direction.Do you sell them? if not, I can\'t seem to find a picture of it so I can fabricate one for this unit.Great looking older unit, would love to get it up and working.Thank You!Tom Whelan

I have a new weatherscope still in box. Call and make an offer 603 608 9670

Hello. Did this unit ever sell? I\'m interested!

I own an original Taylor Windscope Wind Vane w/ original "Wind Direction" indicator.After 30 years of service it needs to have the "distributor " unit either replaced or rebuilt ( currently does not show direction NE thru SE quadrant.What can you do to help ?

I have a Taylor Weatherscope but I need the outdoor parts.Are those available?