Would be interested in wiring diagram for a pavid genset. Model j18gaw-f. Serial 2378. Thanks

Manuals with control drawings available?

A book or parts for a 13k pavid generator.

Hi , I need to know if someone can help me with a Pavid 22KW generator

I needs filter numbers, oil quantity, coolant quantity, and battery size for a Pavid 65kW model 248269 SN 4599 - this is the only information that is available to me. If you have this information please email me at the email address given above. Any help would be greatly appreciated.

We have a Model # 248125, Serial # 1618/s/ng 4023. I need info on this generator, such as natural to lp conversion kit, excitation componennts, manual, and where to get parts for it.Thanks

I just purchased a pavid backup generator. is there parts or service available anywhere for my pavid?

Hi i\'ve got an old pavid brush less Model # G15 H3 Serial # 4290 Kw 187-15 Volts 139WDC it had been working good now it doesn\'t have any outp ut 120 V and 480 V I was wondering if you had any electrical prints or adavice on tings to check out the Unit thanks Cesar

I have an engineer interested in learning more about an old Pravid generator system - where were they made? are parts still available?

I need information about a Pavid/SulliarModel:J35DWH-DHours: Reads 940.4Running Condition:Engine runs ok,generator does not work.Engine:White 4cyl diesel,Serial #VL3441144 D230 X308Measurments:5\'9\"Wide,9\' 6\" Long, 6\' Tall. I appreciate your soon response.Thank you.

I been trying to contact you people a several times,Ineed urgently information about a Pavid generatorModel:J35DWH-DSerial No.:5882/2060Pavid Manufacturing -Co.-Inc.

I need information about a Pavid generator I need parts for this generator,all the information you got on this

Hi,I need the same thing. Ihave a 1976 Pavid 35KW 12 wire and I just need to know how to arrange for 240 volt/3 phase. The factory plate says it\'s wired for 139 volt? Sounds wrong, but it\'s the factory plate. Really simple 4 post configuration inside and all the wires are there, but I can\'t figure it out without the diagram. Post me back a diagram if you have one to mark.777corp@gmail.comThanksMark

Hello, do you have any information on where I could get Pavid radiator hoses?

We are looking for a starter motor for a model G18H3 Pavid generator. The serial number is 2227.

Out-put wiring information. Using Generator for back-up power for manufacturing business. Power 3 phase...

need any manuals for this gen thx

Dear Sirs,I have a Pavid unit on top of the Sullair genset.Model No.: 248275-001Serial No.: 6184I need some information on the functions of the controller board.Does the controller board regulate the RPM of the engine electronically. or does the unit need a solenoid or mechanical govenor.The unit is a 1995 Sullair Genset.Model No.: J75BOM No.: 6716Serial No.: 098G2167 FHOKW - 75Hz - 60Voltage - 277 /480Also, if you have information about where I can get operation and maintenance manuels, I would appreciate it.Thanks in advance,Tom

Hope someone can help me here. I have a pavid generator head, no engine with no id tags. Is there a way to figure out the kw of this unit?I do know this much, It\'s between 35-90 kw, had a hercules diesel, ( most likly a d3000 or d3400). It is of the design that uses an adapter/spacer to join it to the engine. the fan is inside this section. attaches to a #3 flywheel housing. any help would be appreciated. You can email direct at epp@olypen.com. thanks

need info for wiring digrams on gen and controll boxthanks

Hello,I was wondering if you can provide me a manual for the Teledyne Pines machine?thank you

I have a pavid 45 kw generator head, (no engine yet) . It is a 12 wire set that I am told can be wired for 1,2,and 3 phase. It is presently wired 3 phase, parallel Y, 4 wire. Can someone tell me the wiring format for 120/240 single phase, 3 wire? my wires are marked T1-T12.I am aware that I may need to rewire some of the meters but I\'ll deal with that later. Right now I just need to know where the T wires go. thanks

I need an oil pressure switch for a PAVI Generator MOD: G20H3. Yhis is a normally closed switch that starts the engine then cuts the starter off after proving oil pressure.White Diesel EngineMOD: D200S\\N: TH3432857SPEC:X99

I have a Pavid Model G 20 H3. The Crank Timer Board is getting a start signal from the ATS but it is not sending the signal to start the Engine. The unit will start manualy. Is their anything you could suggest. Thank you

Where can my husband get information about the above referenced generator?Thank you.Ruth Turner

Hi, i\'ve got an old c18h3 or g18h3 pavid generator, its hard to tell if its a \'c\' or a \'g\' from the dataplate. It had been working really well untill we went to fire it up to test it before the last ice storm when we noticed that the output was really fluctuating, now it doesn\'t have any output. I was wondering if you had any electrical prints or advice on things to check out on the unit. Thanks Clarence

We have a C18H3 M-G set and we are looking for a wiring diag. Can we purchase a copy of the diag. from your company? We are having problems with the output voltage. Please email us if you can be of asst. Thank You

would a diagram of terminal location for multi voltage be available?

I don\'t know if you found the information on re-straping your generator or not but if you still need a print, e-mail me and I\'ll send you what you need.

I HAVE A PAVID GEN SET MODEL J13GAW-HNEED WIRING DIAG. TO CHANGE FROM 480V 3 PHASE TO 240V 3 PHASETHANKSJIM KITSON