i would like to know if you can repair the motor control board on this for me and how much, or is it better and cheaper just to buy a new one from you. do you sell these boards and if not can you tell me someone that does. thanks.
If you need your Cybex unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110
Need to know the wiring sequence for the 4 wire tach pins. The connector was broken off, wires are dangling, there are 4 bare pins for the tach need to know the wire sequence. Please help me.
Hello: I have an inoperable Trotter 540 Supertrainer, Model 540 ST, Serial No. D1217017, speed 1 to 10mph, 115 volt, vac 68z, 9 amp 1 phase that I would like diagnosed and repaired. If you are able to 1) refer me to someone who can do this, 2) provide the services yourself, please let me know at your earliest convenience. If you are providing the service, please provide your terms.
I have a Trotter 510 which until recently it was working fine.Now after some 10 minutes of operation it stops abruptly and gives a Code 2 (excessive Current Draw) indication.The current here is 110 v 50Hz but I do not think the problem is the frequency, otherwise it could not have operated OK for a couple of years.The total time is 281hours, the total distance is 880 miles and the number of starts 1457.Brushes were (or look) OKIf you can diagnose the problem please advise what parts (motor, relay box, etc.) may need changing and give me a quote.Because of our geographic location, shipping the treadmill back would be prohibitively expensive as would be flying a mechanic.And the machine is too young to junk it.Please see what you can do.
I have Trotter 540 Supertrainer, Model 540 ST, Serial E6540ST 03340 and in only runs at speed of 1 mph. No other controls will work. I would like control board repaired or purchase a new, used or rebuilt one.thanks, Lee.......
WE received the S-2 maintenance code. Flipped the deck but can\'t clear S-2 maintenance code. Please help.
I have misplaced my owners manual for my treadmill, would you please send me an electronic manual? Thank you.Steve Riemann, Owner
i\'ve diagnosed the treadmill using the manual and suspect the upper board (in console) is the problem. can you test it? can i also send the other boards in case it test ok?thanks
The tredmill belogs to by parents. When I go on it it gives the sensation that I am slipping on Ice. When I jog on to every time my foot comes down on the belt the belt stops for halve a second. Also the belt moves toward the right when I am using the machine
Sorry by my english!!! I have a controller motor board Cybex 700 T,need to repair this controller board, I live in Venezuela but I can send you. Thanks for Your cooperation and what can help me! Gustavo Ramirez
i have two cybex treadmill\'s that need repaired. i think a fuse blew in one and the other one does not hold it\'s speed.
I need an overlay keypad for a Trotter 510 Treadmill. The + key is stuck on mine. I am having problems finding this part.
I am receiving a free Cybex machine without a users manual. It works, but I am wondering if I need to have it checked out before I get something I regret.
When I press the start button, it displays \"SAFE\" on the LED. Is there a manual that I can obtain from you to run a procedure to make this treadmill run again?Thank you
i would like to know if you can repair the motor control board on this for me and how much, or is it better and cheaper just to buy a new one from you. do you sell these boards and if not can you tell me someone that does. thanks.
need to order parts could you send a manual for the trotter 540. Thank you.
I need help re-aligning the belt on my treatmill, it slipped to one side and now I cannot get it to stop slipping.
do care cybex main borads (Trotter 510) rebuilt is fineDavid Gebauer (209) 267-9116 ask for Tim----
I would like to know if you can repair the motor control board on a trotter 645 treadmill board. I can take it out and send it to you how much would this cost or do you have used one I could purchase. If you can not fix do you know a where I could find a used one? or where I could possibly look.thank you,Ken Garcia
I have Cybex Q20 ci. I am unable to press the start button to initiate functions to use the pre program that I have set up. I tried turning it on and off the machine a few times and sometimes then it will allow me to press the start button to activate the prgram. Then the next day I use it it doesn\'t work again & by turning it on and off the machine a few times it doesn\'t work. Its not the not the pin that is clipped to your shirt/pant that when you pull it out of the slot from the panel the machine stops. I am not sure if it the main circuit boad on top?
I have Cybex Q20 ci. I am unable to press the start button to initiate functions to use the pre program that I have set up. I tried turning it on and off the machine a few times and sometimes then it will allow me to press the start button to activate the prgram. Then the next day I use it it doesn\'t work again & by turning it on and off the machine a few times it doesn\'t work. Its not the not the pin that is clipped to your shirt/pant that when you pull it out of the slot from the panel the machine stops. I am not sure if it the main circuit boad on top?
Just picked up a trotter 540 and need a manual or info on how to program it (what are the programs what they do and how to program them). Also how to care for the machine. Belt lubrication?....and such.Can you help?Thanks
I have a cybex q20 ci. it is old but runs great. It is stuck in the elevation mode. i need a manual to see how to fix it.
I am looking for this manual if you could please email it to me.
I sure need a copy of the Cybex Trotter 540 Supertrainer owners manual.thanks,
#Cybex by Ed Myszka on 2006-06-24 21:59